Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY
RM25T0E _52 Drivetrain _029905 DRIVE SHAFT / PROPELLER SHAFT _0138402 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.REMOVE SPIDER BEARING

HINT:

Use the same procedure for both spiders.


a.
C307725C01
1.552,0.906 0.938,0.49 0.938,0.49 1.802,0.677 false 0.729,0.396 1.042,0.594 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange yoke and propeller shaft.


b.
C307728

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


c.

Using 2 screwdrivers, remove the 4 rear propeller shaft joint spider bearing snap rings from the grooves.


d.
C307741C01
0.938,0.938 0.729,1.135 true 3.115,1.135 2.594,1.135 true 1.042,0.083 1.354,0.281 0.313,0.198 10 false *a 1.427,0.823 1.74,1.021 0.313,0.198 10 false *b 0.99,0.865 1.302,1.063 0.313,0.198 10 false SST 3.167,1.073 3.323,1.271 0.156,0.198 10 false A
*a Turn
*b Hold


Using SST, remove the spider bearing from the sleeve yoke.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



e.
C258199C03
2.906,1.156 2.656,1.156 2.656,1.156 2.344,0.729 true 2.99,1.073 3.188,1.25 0.198,0.177 10 false *a
*a Hammering Point


Remove the flange yoke with a hammer.

HINT:

Remove the spider bearing on the opposite side using the same procedure.


NOTICE:

Do not tap the shaft.



f.

Remove the flange yoke from the propeller shaft assembly.


g.
C307746C01
2.125,1.146 2.5,1.146 true 0.573,1.188 0.948,1.188 true 1.656,0.604 1.969,0.802 0.313,0.198 10 false *a 0.438,0.177 0.781,0.385 0.344,0.208 10 false *b 1.948,1.083 2.156,1.313 0.208,0.229 10 false A 0.26,1.115 0.656,1.313 0.396,0.198 10 false SST
*a Turn
*b Hold


Install the 2 removed spider bearing outer races to the spider.


h.

Using SST, remove the spider bearing from the flange yoke.

SST
09332-25010  

HINT:

Sufficiently raise the part indicated by A so that it does not come into contact with the spider bearing.



i.
C258224C01
1.396,0.313 1.823,0.313 1.823,0.313 2.417,0.604 true 1.188,0.219 1.406,0.417 0.219,0.198 10 *a
*a Hammering Point


Tap off the flange yoke with a hammer.


j.

Remove the spider.