84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)
w/ intermittent function:
Check the front wiper intermittent operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L23-3 (+1) and a negative (-) lead to terminal L22-2 (EW).
Turn the wiper switch to the INT position.
Operate the intermittent wiper and check the voltage between terminals L23-3 (+1) and L22-2 (EW).
Voltage changes as shown in the illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
Check the front washer operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L22-3 (WF) and a negative (-) lead to terminal L22-2 (EW).
Turn the ignition switch to ON.
Turn the washer switch on and off, and check the voltage between terminals L22-3 (WF) and L22-2 (EW).
Voltage changes as shown in the following illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
w/ rear washer:
Check the rear washer operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L23-5 (WR) and a negative (-) lead to terminal L22-2 (EW).
Turn the ignition switch to ON.
Turn the washer switch on and off, and check the voltage between terminals L23-5 (WR) and L22-2 (EW).
Voltage changes as shown in the following illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)
w/ intermittent function, w/ intermittent timing adjustment:
Check the front wiper intermittent operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L23-2 (+1) and a negative (-) lead to terminal L22-2 (EW).
Turn the wiper switch to the INT position.
Operate the intermittent wiper and check the voltage between terminals L23-2 (+1) and L22-2 (EW).
Voltage changes as shown in the illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
w/ intermittent function, w/o intermittent timing adjustment:
Check the front wiper intermittent operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L23-2 (+1) and a negative (-) lead to terminal L22-2 (EW).
Turn the wiper switch to the INT position.
Operate the intermittent wiper and check the voltage between terminals L23-2 (+1) and L22-2 (EW).
Voltage changes as shown in the illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
Check the front washer operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L22-1 (WF) and a negative (-) lead to terminal L22-2 (EW).
Turn the ignition switch to ON.
Turn the washer switch on and off, and check the voltage between terminals L22-1 (WF) and L22-2 (EW).
Voltage changes as shown in the following illustration.
If the result is not as specified, replace the windshield wiper switch assembly.
w/ rear washer:
Check the rear washer operation.
| *a | Component with harness connected (Windshield Wiper Switch Assembly) |
Connect a voltmeter positive (+) lead to terminal L23-10 (WR) and a negative (-) lead to terminal L22-2 (EW).
Turn the ignition switch to ON.
Turn the washer switch on and off, and check the voltage between terminals L23-10 (WR) and L22-2 (EW).
Voltage changes as shown in the following illustration.
If the result is not as specified, replace the windshield wiper switch assembly.