Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM25T0E _59 Vehicle Exterior _029939 WIPER / WASHER _0138366 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.

Check the front wiper switch.

i.
E257039C44
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.24,1.083 1.135,0.531 true 1.75,0.5 1.625,1.063 true 1.458,0.51 1.427,1.063 true 1.042,1.063 0.792,0.573 true 0.229,0.208 0.542,0.406 0.313,0.198 10 false *a 0.49,1.031 0.802,1.229 0.313,0.198 10 false L23 2.667,1.042 2.979,1.24 0.313,0.198 10 false L22 1.01,0.354 1.323,0.552 0.313,0.198 10 false +1 1.354,0.333 1.667,0.531 0.313,0.198 10 false +B 1.688,0.333 2,0.531 0.313,0.198 10 false +S 0.688,0.375 1,0.573 0.313,0.198 10 false +2
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ intermittent:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-3 (+1) - L23-1 (+S) OFF Below 1 Ω
INT
L23-3 (+1) - L23-2 (+B) MIST
LO
L23-4 (+2) - L23-2 (+B) HI


If the result is not as specified, replace the windshield wiper switch assembly.


ii.

w/o intermittent:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-3 (+1) - L23-1 (+S) OFF Below 1 Ω
L23-3 (+1) - L23-2 (+B) MIST
LO
L23-4 (+2) - L23-2 (+B) HI


If the result is not as specified, replace the windshield wiper switch assembly.



b.
E257039C46
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.969,1.052 1.719,0.448 true 2.302,0.479 2.156,1.083 true 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 0.49,1.031 0.802,1.229 0.313,0.198 10 false L23 2.667,1.042 2.979,1.24 0.313,0.198 10 false L22 1.604,0.281 1.917,0.479 0.313,0.198 10 false WF 2.198,0.26 2.51,0.458 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Check the front washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L22-3 (WF) - L22-2 (EW) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



c.
E257039C47
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.844,1.75 1.979,1.354 true 2.281,0.521 2.156,1.083 true 2.219,1.75 2.125,1.344 true 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.031 0.802,1.229 0.313,0.198 10 false L23 2.667,1.042 2.979,1.24 0.313,0.198 10 false L22 1.698,1.802 2.01,2 0.313,0.198 10 false +1R 2.208,0.365 2.521,0.563 0.313,0.198 10 false EW 2.104,1.802 2.417,2 0.313,0.198 10 false C1R
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ rear wiper:

Check the rear wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L22-6 (C1R) - L22-2 (EW) LO Below 1 Ω
L22-7 (+1R) - L22-2 (EW) HI
L22-6 (C1R) - L22-2 (EW)
L22-7 (+1R) - L22-2 (EW)
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



d.
E257039C48
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.5,1.823 1.635,1.333 true 2.281,0.521 2.156,1.083 true 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.031 0.802,1.229 0.313,0.198 10 false L23 2.667,1.042 2.979,1.24 0.313,0.198 10 false L22 1.396,1.844 1.708,2.042 0.313,0.198 10 false WR 2.208,0.365 2.521,0.563 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ rear wiper:

Check the rear washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-5 (WR) - L22-2 (EW) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.

Check the front wiper switch.

i.
B383412C07
0.417,1.063 0.76,1.323 0.344,0.26 2.677,1.073 3.021,1.333 0.344,0.26 1.781,1.042 1.615,0.521 true 2.156,1.073 2.229,0.531 true 2.385,1.083 2.552,0.542 true 2,1.052 1.896,0.531 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.469,1.115 0.927,1.313 0.458,0.198 10 false L22 2.74,1.125 3.198,1.323 0.458,0.198 10 false L23 1.458,0.344 1.771,0.542 0.313,0.198 10 false +S 2.177,0.344 2.49,0.542 0.313,0.198 10 false +1 2.51,0.344 2.823,0.542 0.313,0.198 10 false +2 1.781,0.344 2.094,0.542 0.313,0.198 10 false +B
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ intermittent:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-2 (+1) - L23-4 (+S) OFF Below 1 Ω
INT
L23-2 (+1) - L23-3 (+B) MIST
LO
L23-1 (+2) - L23-3 (+B) HI


If the result is not as specified, replace the windshield wiper switch assembly.


ii.
B383412C07
0.417,1.063 0.76,1.323 0.344,0.26 2.677,1.073 3.021,1.333 0.344,0.26 1.781,1.042 1.615,0.521 true 2.156,1.073 2.229,0.531 true 2.385,1.083 2.552,0.542 true 2,1.052 1.896,0.531 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.469,1.115 0.927,1.313 0.458,0.198 10 false L22 2.74,1.125 3.198,1.323 0.458,0.198 10 false L23 1.458,0.344 1.771,0.542 0.313,0.198 10 false +S 2.177,0.344 2.49,0.542 0.313,0.198 10 false +1 2.51,0.344 2.823,0.542 0.313,0.198 10 false +2 1.781,0.344 2.094,0.542 0.313,0.198 10 false +B
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/o intermittent:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-2 (+1) - L23-4 (+S) OFF Below 1 Ω
L23-2 (+1) - L23-3 (+B) MIST
LO
L23-1 (+2) - L23-3 (+B) HI


If the result is not as specified, replace the windshield wiper switch assembly.



b.
B383412C08
0.417,1.063 0.76,1.323 0.344,0.26 2.677,1.073 3.021,1.333 0.344,0.26 1.25,1.063 1.073,0.479 true 1.448,1.052 1.583,0.5 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.469,1.115 0.927,1.313 0.458,0.198 10 false L22 2.74,1.125 3.198,1.323 0.458,0.198 10 false L23 0.979,0.302 1.292,0.5 0.313,0.198 10 false EW 1.469,0.302 1.781,0.5 0.313,0.198 10 false WF
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Check the front washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L22-1 (WF) - L22-2 (EW) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



c.
B383412C09
0.417,1.063 0.76,1.323 0.344,0.26 2.677,1.073 3.021,1.333 0.344,0.26 1.25,1.063 1.073,0.479 true 1.594,1.802 1.438,1.354 true 1.302,1.823 1.302,1.333 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.469,1.115 0.927,1.313 0.458,0.198 10 false L22 2.74,1.125 3.198,1.323 0.458,0.198 10 false L23 0.979,0.302 1.292,0.5 0.313,0.198 10 false EW 1.542,1.854 1.854,2.052 0.313,0.198 10 false +1R 1.167,1.854 1.479,2.052 0.313,0.198 10 false C1R
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ rear wiper:

Check the rear wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L22-5 (C1R) - L22-2 (EW) LO Below 1 Ω
L22-4 (+1R) - L22-2 (EW) HI
L22-5 (C1R) - L22-2 (EW)
L22-4 (+1R) - L22-2 (EW)
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



d.
B383412C10
0.417,1.063 0.76,1.323 0.344,0.26 2.677,1.073 3.021,1.333 0.344,0.26 1.25,1.063 1.073,0.479 true 1.969,1.844 1.792,1.333 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.469,1.115 0.927,1.313 0.458,0.198 10 false L22 2.74,1.125 3.198,1.323 0.458,0.198 10 false L23 0.979,0.302 1.292,0.5 0.313,0.198 10 false EW 1.917,1.885 2.229,2.083 0.313,0.198 10 false WR
*a Component with harness connected
(Windshield Wiper Switch Assembly)


w/ rear wiper:

Check the rear washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L23-10 (WR) - L22-2 (EW) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.