Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Long Body)
RM25T0E _58 Vehicle Interior _029930 SEAT _0140343 REAR NO. 2 SEAT ASSEMBLY(for Long Body) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Long Body)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 71034A 1.INSTALL REAR NO. 1 SIDE SEAT CUSHION LEG SUB-ASSEMBLY LH (for Rear Side Seat Assembly LH)

B385657

a.

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Install the rear No. 1 side seat cushion leg sub-assembly LH with the 2 pins and 2 E-rings as shown in the illustration.



b.

w/o Rear No. 2 Seat Inner Belt Assembly:

i.

Install the 2 torsion springs, rear No. 1 side seat cushion leg sub-assembly LH with the 2 pins and 2 new E-rings as shown in the illustration.



Hide 79929 2.INSTALL FOLD SEAT LEG STOPPER FRAME (for Rear Side Seat Assembly LH)

B385658

a.

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Temporarily install the fold seat leg stopper frame and 4 plate washers.


ii.

Set a new spring nut, 12 mm socket wrench and extension bar as shown in the illustration.


iii.

Using a plastic-faced hammer, tap the extension bar to insert the spring nut into the groove and install the fold seat leg stopper frame.

HINT:

Use the same procedure for the other side.




Hide 72660A 3.INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY (for Rear Side Seat Assembly LH)

a.

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Install the 2 bolts, 2 spacers and rear seat cushion support assembly.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)



Hide 71089B 4.INSTALL REAR SIDE SEATBACK COVER SUB-ASSEMBLY LH (for Rear Side Seat Assembly LH)

B385655C01
1.896,3.188 1.5,2.396 false 1.271,2.177 1.583,2.375 0.313,0.198 10 false *1
*1 Hog Ring Pliers


a.

Using hog ring pliers, install the rear side seatback pad LH and 7 new hog rings to rear side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




b.
B385653C01
2.073,3.708 1.844,3.146 false 1.729,2.948 2.042,3.146 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the rear side seatback cover sub-assembly LH and 4 new hog rings to rear side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




c.
B386175C01
1.854,3.573 2.031,2.74 false 0.875,3.625 0.979,2.865 false 2.021,2.469 2.333,2.667 0.313,0.198 10 false *1 0.708,3.698 1.021,3.896 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


Install 6 new hog rings.

NOTICE:
·

Be careful not to damage the rear side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.



Hide 71086B 5.INSTALL REAR SIDE SEAT CUSHION COVER SUB-ASSEMBLY LH (for Rear Side Seat Assembly LH)

B386177C01
2.01,4.125 1.865,3.552 false 0.354,2.802 0.729,3.302 true 0.167,2.677 0.479,2.875 0.313,0.198 10 false *a 1.979,4.167 2.292,4.365 0.313,0.198 10 false *1
*1 Hog Ring Pliers
*a Cutout


a.

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Using hog ring pliers, install the rear side seat cushion cover sub-assembly LH and 18 new hog rings to rear side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.




b.
B386176C01
1.854,3.26 2.052,2.521 false 0.719,3.281 0.26,2.906 true 2.042,2.354 2.354,2.552 0.313,0.198 10 false *1 0.094,2.771 0.406,2.969 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


w/o Rear No. 2 Seat Inner Belt Assembly:

i.

Using hog ring pliers, install the rear side seat cushion cover sub-assembly LH and 16 new hog rings to rear side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.



ii.

Install the 2 pieces of fastening tape.



Hide 71034B 6.INSTALL REAR NO. 2 SIDE SEAT CUSHION LEG SUB-ASSEMBLY LH (for Rear No. 2 Side Seat Assembly LH)

a.
B385562

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Install the rear No. 2 side seat cushion leg sub-assembly LH with the 2 pins and 2 new E-rings as shown in the illustration.



b.

w/o Rear No. 2 Seat Inner Belt Assembly:

i.

Install the 2 torsion springs, rear No. 2 side seat cushion leg sub-assembly LH with the 2 pins and 2 new E-rings as shown in the illustration.



Hide 79929A 7.INSTALL NO. 2 FOLD SEAT LEG STOPPER FRAME (for Rear No. 2 Side Seat Assembly LH)

a.
B385658

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Temporarily install the No. 2 fold seat leg stopper frame and 4 plate washers.


ii.

Set a new spring nut, 12 mm socket wrench and extension bar as shown in the illustration.


iii.

Using a plastic-faced hammer, tap the extension bar to insert the spring nut into the groove and install the fold seat leg stopper frame.

HINT:

Use the same procedure for the other side.




Hide 72660A 8.INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY (for Rear No. 2 Side Seat Assembly LH)

a.

w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Install the 2 bolts, 2 spacers and rear seat cushion support assembly.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)



Hide 71089C 9.INSTALL REAR NO. 2 SIDE SEATBACK COVER SUB-ASSEMBLY LH (for Rear No. 2 Side Seat Assembly LH)

B385563C01
1.979,3.229 2.021,2.594 false 1.969,2.427 2.281,2.625 0.313,0.198 10 false *1
*1 Hog Ring Pliers


a.

Using hog ring pliers, install the rear No. 2 side seatback pad LH and 7 new hog rings to rear No. 2 side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear No. 2 side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




b.
B385564C01
2.021,3.615 2.167,3.188 false 2.146,3.031 2.458,3.229 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the rear No. 2 side seatback cover sub-assembly LH and 4 new hog rings to rear No. 2 side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear No. 2 side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




c.
B382609C01
1.885,2.74 2.094,2.156 false 0.542,2.708 1.177,2.229 true 2.052,1.99 2.365,2.188 0.313,0.198 10 false *1 0.354,2.635 0.667,2.833 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


Install 6 new hog rings.

NOTICE:
·

Be careful not to damage the rear No. 2 side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.



Hide 71086B 10.INSTALL REAR SIDE SEAT CUSHION COVER SUB-ASSEMBLY LH (for Rear No. 2 Side Seat Assembly LH)

a.

Install the rear No. 2 side seat cushion pad LH to rear No. 2 side seat frame assembly.


b.
B386172C01
1.865,3.104 1.948,2.573 false 0.292,3.656 0.75,3.146 true 1.917,2.417 2.229,2.615 0.313,0.198 10 false *1 0.156,3.677 0.469,3.875 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


w/ Rear No. 2 Seat Inner Belt Assembly:

i.

Using hog ring pliers, install the rear side seat cushion cover sub-assembly LH and 18 new hog rings to rear No. 2 side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear No. 2 side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.




c.
B386173C01
1.906,3.094 2,2.396 false 0.323,3.552 0.76,3.167 true 1.969,2.229 2.281,2.427 0.313,0.198 10 false *1 0.135,3.51 0.448,3.708 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


w/o Rear No. 2 Seat Inner Belt Assembly:

i.

Using hog ring pliers, install the rear side seat cushion cover sub-assembly LH and 16 new hog rings to rear No. 2 side seat frame assembly LH.

NOTICE:
·

Be careful not to damage the rear No. 2 side seatback pad LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.



HINT:

Install the hog rings at the cutouts.



ii.

Install the 2 pieces of fastening tape.