Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM25T0E _59 Vehicle Exterior _029939 WIPER / WASHER _0140602 WIPER AND WASHER SYSTEM D

WIPER / WASHER  WIPER AND WASHER SYSTEM  SYSTEM DESCRIPTION  


WASHER-LINKED OPERATION


a.

This system operates the front wipers at low speed immediately after a jet of washer fluid when the front washer switch is turned on for 0.3 seconds or more.

The system operates the front wipers at low speed for approximately 2.2 seconds and then stops operation when the washer switch is turned on for 1.5 seconds or more.

E189998E05
3.854,0.406 3.615,0.406 3.615,0.406 3.479,0.948 false 4.49,3.177 4.229,3.177 4.229,3.177 4.135,2.865 false 0.135,0.135 1.385,0.5 1.25,0.365 12 false Timing Chart: 4.5,1.167 6.354,1.583 1.854,0.417 10 false Approximately 0.3 Seconds 3.906,0.302 5.76,0.719 1.854,0.417 10 false Washer Switch On Time 4.563,3.104 6.417,3.521 1.854,0.417 10 false Additional Wiper Operation 0.74,1.177 1.844,1.5 1.104,0.323 10 false Windshield Wiper Switch 0.74,2.083 1.865,2.542 1.125,0.458 10 false Windshield Wiper Motor Assembly 2.188,1.01 2.521,1.292 0.333,0.281 10 false On 2.188,1.406 2.521,1.688 0.333,0.281 10 false Off 2.188,1.927 2.521,2.208 0.333,0.281 10 false On 2.177,2.323 2.51,2.604 0.333,0.281 10 false Off

Washer Switch On Time Additional Wiper Operation
0.2 seconds or less None
Between 0.3 seconds and 1.4 seconds 1 time
1.5 seconds or more 3 times



INTERMITTENT OPERATION


*: w/ Intermittent Time Adjust Dial


a.

The system operates the front wipers at approximately 1.6 to 10.7 second intervals when the front wiper switch is turned to the INT position. The intermittent time can be adjusted from 1.6 to 10.7 seconds by using the intermittent time adjust dial.*


b.

If the front wiper switch is turned to the INT position, current flows from the already charged capacitor C1 through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, to terminal +1 of the windshield wiper motor, to the windshield wiper motor and finally to ground, causing the windshield wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch and then INT2. When the current flow from capacitor C1 ends, Tr1 turns off to stop the relay contact point and halt the windshield wiper motor.

When the relay contact point turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact point turns on, causing the windshield wiper motor to operate again. This cycle is the intermittent operation.

The intermittent time can be adjusted by using the intermittent time adjust dial (variable resistor) to change the charge time of capacitor C1.*

E305987E01
2.25,0.24 2.563,0.438 0.313,0.198 10 false +B 2.594,0.25 2.906,0.448 0.313,0.198 10 false +2 2.979,0.25 3.292,0.448 0.313,0.198 10 false +1 3.323,0.25 3.635,0.448 0.313,0.198 10 false +S 0.177,1.25 1.292,1.604 1.115,0.354 10 false Windshield Wiper Switch Assembly 4.052,1.719 4.365,1.917 0.313,0.198 10 false *1 4.979,2.823 5.438,3.021 0.458,0.198 10 false Tr1 5.521,2.594 5.979,2.792 0.458,0.198 10 false Tr2 3.906,3.229 4.219,3.427 0.313,0.198 10 false C1 5.917,3.229 6.229,3.427 0.313,0.198 10 false C2 1.281,5.115 2.51,5.313 1.229,0.198 10 false OUT WIP2 1.292,6.781 2.521,6.979 1.229,0.198 10 false OUT WIP1 0.083,6.188 0.865,6.552 0.781,0.365 10 false Limit Switch Assembly 3.604,6.438 4.063,6.635 0.458,0.198 10 false WIP 2.24,6.583 3.156,6.781 0.917,0.198 10 false ECU IG 5.156,5.417 6.25,5.771 1.094,0.354 10 false Windshield Wiper Motor Assembly 5.885,0.896 6.344,1.094 0.458,0.198 10 false OFF 5.917,1.073 6.229,1.271 0.313,0.198 10 false ON 6.604,0.719 6.917,0.917 0.313,0.198 10 false EW 6.26,0.719 6.573,0.917 0.313,0.198 10 false WF 3.667,0.25 4.281,0.448 0.615,0.198 10 false INT1 4.01,0.25 4.625,0.448 0.615,0.198 10 false INT2 4.438,0.26 5.052,0.458 0.615,0.198 10 false B1 1.781,0.448 2.396,0.646 0.615,0.198 10 false MIST 1.781,0.635 2.396,0.833 0.615,0.198 10 false OFF 1.813,0.813 2.427,1.01 0.615,0.198 10 false ON 1.833,0.99 2.448,1.188 0.615,0.198 10 false LO 1.854,1.177 2.469,1.375 0.615,0.198 10 false HI 1.438,1.385 2.198,1.719 0.76,0.333 10 false Front Wiper Switch 1.427,2.542 2.188,2.875 0.76,0.333 10 false Front Wiper Relay 5.438,1.281 6.302,1.615 0.865,0.333 10 false Front Washer Switch 2.125,3.677 2.438,3.875 0.313,0.198 10 false +B 2.49,3.677 2.802,3.875 0.313,0.198 10 false +2 2.854,3.677 3.167,3.875 0.313,0.198 10 false +1 3.271,3.688 3.583,3.885 0.313,0.198 10 false +S 6.479,3.667 6.792,3.865 0.313,0.198 10 false EW 6.063,3.677 6.375,3.875 0.313,0.198 10 false WF 3.708,5.083 4.021,5.281 0.313,0.198 10 false +2 4.021,5.083 4.333,5.281 0.313,0.198 10 false +1 4.333,5.094 4.646,5.292 0.313,0.198 10 false +S 4.74,5.083 4.896,5.281 0.156,0.198 10 false B 4.073,5.583 4.229,5.781 0.156,0.198 10 false E 4.698,6.271 7.146,6.469 2.448,0.198 10 false from IG1 2 Relay 4.688,6.635 7.135,6.833 2.448,0.198 10 false from IG1 1 Relay*2 3.292,5.271 3.604,5.469 0.313,0.198 10 false *3 0.875,7.104 1.188,7.302 0.313,0.198 10 false *2 0.198,7.615 3.021,7.813 2.823,0.198 10 false *1: w/ Intermittent Time Adjust Dial 0.208,8 3.656,8.271 3.448,0.271 10 false *2: for Model Code #J71 Series, Canvas Top 0.198,8.417 3.458,8.656 3.26,0.24 10 false *3: except Model Code #J71 Series, Canvas Top 5.188,4.74 6.792,5.094 1.604,0.354 10 false Windshield Washer Motor and Pump Assembly



REAR WIPER INTERMITTENT OPERATION (w/ Rear Wiper and Washer System)


a.

When the rear wiper switch is turned to the INT position, current flows from the capacitor of the intermittent operation control circuit to turn on the transistor. Current flows from terminal B of the rear wiper relay, to the relay coil, to the transistor, to terminal C1 of the rear wiper relay, to terminal C1R of the rear wiper control switch and finally to ground, causing the relay contact point to turn on.

When the relay contact point turns on, current flows from terminal B of the rear wiper relay to the relay contact point, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor, to the rear wiper motor and finally to ground, causing the rear wiper motor to operate. The transistor turns off immediately after the rear wiper motor operation as the current flow from the capacitor ends, causing the relay contact point to turn off.

Even when the relay contact point turns off, current flows from terminal B of the rear wiper motor, to the relay contact point in the rear wiper motor, to terminal S of the rear wiper motor, to terminal +SM of the rear wiper relay, to the contact point of the rear wiper relay, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor and finally to ground until the rear wiper motor stops at the automatic stop position. Then the rear wiper motor stops at the automatic stop position as the relay contact point in the rear wiper motor turns off.

The capacitor in the intermittent operation control circuit is charged in approximately 8 +/-2 seconds after the current flow ends. After the charge is completed, current starts flowing again to turn on the transistor, causing the relay contact point to turn on.

This cycle of current flow and charging described above is the intermittent operation.

E305988E01
0.052,2.802 2.5,3 2.448,0.198 10 false from IG1 2 Relay 1.427,4.156 1.74,4.354 0.313,0.198 10 false +1 1.542,5.208 1.698,5.406 0.156,0.198 10 false E 1.917,4.146 2.073,4.344 0.156,0.198 10 false S 2.323,4.156 2.479,4.354 0.156,0.198 10 false B 3.688,5.052 4.094,5.594 0.406,0.542 10 false INT Circuit 3.344,3.031 7.156,3.24 3.813,0.208 10 false Rear Washer Motor Assembly 1.865,5.458 2.979,5.823 1.115,0.365 10 false Rear Wiper Motor Assembly 3.573,6.396 7.156,6.615 3.583,0.219 10 false Rear Wiper Relay Assembly 4.938,4.135 5.094,4.333 0.156,0.198 10 false B 5.115,4.417 5.427,4.615 0.313,0.198 10 false LM 5.021,4.698 5.406,4.906 0.385,0.208 10 false +SM 4.99,5.146 5.448,5.344 0.458,0.198 10 false LSW 5.135,5.99 5.448,6.188 0.313,0.198 10 false C1 4.448,5.823 4.906,6.021 0.458,0.198 10 false Tr3 4.531,0.865 5.146,1.063 0.615,0.198 10 false WASH 4.594,1.052 5.052,1.25 0.458,0.198 10 false OFF 4.427,1.24 4.885,1.438 0.458,0.198 10 false INT 4.823,1.24 5.135,1.438 0.313,0.198 10 false LO 5.896,0.698 6.354,0.896 0.458,0.198 10 false +1R 4.417,1.427 4.729,1.625 0.313,0.198 10 false ON 4.865,1.427 5.177,1.625 0.313,0.198 10 false HI 4.385,1.604 5.458,1.802 1.073,0.198 10 false ON+WASH 5.188,0.688 5.5,0.885 0.313,0.198 10 false WR 5.552,0.688 6.01,0.885 0.458,0.198 10 false C1R 6.292,0.688 6.604,0.885 0.313,0.198 10 false EW 1.573,2.958 2.031,3.156 0.458,0.198 10 false WIP 1.396,1.052 6.135,1.25 4.74,0.198 10 false Windshield WiperSwitch Assembly 5.01,1.979 5.323,2.177 0.313,0.198 10 false WR 5.385,1.99 5.844,2.188 0.458,0.198 10 false C1R 5.76,1.99 6.219,2.188 0.458,0.198 10 false +1R 6.135,1.99 6.448,2.188 0.313,0.198 10 false EW