RM25T0E _V1 General _029810 SPECIFICATIONS _0141509 1HZ ENGINE MECHANICAL F
SPECIFICATIONS 1HZ ENGINE MECHANICAL TORQUE SPECIFICATIONS
ENGINE
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Injection pump x Timing gear case sub-assembly |
18 |
184 |
13 |
| Injection pump x Injection pump stay |
69 |
704 |
51 |
| Plug bolt x Distributive head plug |
16.7 |
170 |
12 |
DRIVE BELT
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Generator assembly |
for bolt A |
19.6 |
200 |
14 |
|
for bolt B |
59 |
602 |
44 |
| Nut x Idle pulley bracket |
40 |
408 |
30 |
TIMING BELT
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
in.*lbf |
| Camshaft timing pulley x Camshaft |
98 |
999 |
72 |
|
| Cylinder head cover sub-assembly x Cylinder head sub-assembly |
6.4 |
65 |
|
57 |
| Camshaft drive gear x Injection pump |
31 |
316 |
23 |
|
| No. 1 timing belt idler sub-assembly x No. 2 timing gear cover |
34.5 |
352 |
25 |
|
| No. 1 chain tensioner assembly x No. 2 timing gear cover |
13 |
133 |
10 |
|
| No. 1 timing belt cover x Camshaft oil seal retainer and No. 2 timing gear cover |
6.4 |
65 |
|
57 |
Camshaft
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Camshaft bearing cap x Cylinder head |
for No. 1 camshaft bearing cap bolt |
24.5 |
250 |
18 |
|
for other bolt |
18.1 |
185 |
13 |
| Camshaft oil seal retainer x Cylinder head sub-assembly |
19.6 |
200 |
14 |
CYLINDER HEAD GASKET
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Cylinder head sub-assembly x Cylinder block |
Step 1 |
68.6 |
700 |
51 |
|
Step 2 |
90° |
|
Step 3 |
90° |
FRONT CRANKSHAFT OIL SEAL
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Crankshaft pulley x Crankshaft |
430 |
4385 |
317 |
| No. 2 crankshaft pulley x Crankshaft pulley |
24.5 |
250 |
18 |
REAR CRANKSHAFT OIL SEAL
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| Rear end plate x Cylinder block |
18.1 |
185 |
13 |
| Flywheel sub-assembly x Crankshaft |
127.4 |
1299 |
94 |
ENGINE ASSEMBLY
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
in.*lbf |
| Front engine mounting insulator RH x Mounting bracket |
83 |
846 |
61 |
|
| Front engine mounting insulator LH x Mounting bracket |
83 |
846 |
61 |
|
| Front engine mounting insulator RH x Body |
74 |
755 |
55 |
|
| Front engine mounting insulator LH x Body |
87 |
887 |
64 |
|
| Outlet heater water hose x Intake manifold and body |
for bolt A |
5.0 |
51 |
|
44 |
|
for bolt B |
17.5 |
178 |
13 |
|
for LHD 2 Battery: Ground cable x Cylinder block |
39 |
398 |
29 |
|
| Battery to ground cable x Cylinder block |
35 |
357 |
26 |
|
| Vane pump assembly x Timing gear case |
29 |
296 |
21 |
|
| Vane pump oil reservoir assembly x Intake manifold |
18 |
184 |
13 |
|
| Cooler compressor assembly x No. 1 compressor mounting bracket |
24 |
245 |
18 |
|
| Air cleaner case x Body |
18 |
184 |
13 |
|
| Hood sub-assembly x Body |
20 |
204 |
15 |
|
ENGINE UNIT
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
in.*lbf |
| Rear engine oil seal retainer x Cylinder block |
6.4 |
65 |
|
57 |
| Oil pan drain plug x Oil pan sub-assembly |
34.3 |
350 |
25 |
|
| No. 1 idle gear x Cylinder block |
68 |
693 |
50 |
|
| No. 2 timing gear cover x Cylinder block |
19.6 |
200 |
14 |
|
| Engine hanger x Cylinder head sub-assembly |
39.2 |
400 |
29 |
|
| No. 1 water by-pass pipe x Cylinder block |
19.6 |
200 |
14 |
|
| No. 1 compressor mounting bracket x Cylinder head sub-assembly |
39 |
398 |
29 |
|
| Idle pulley bracket x No. 1 compressor mounting bracket |
39 |
398 |
29 |
|
| Outlet water x Cylinder head sub-assembly |
19.6 |
200 |
14 |
|
| Vacuum pump assembly x No. 2 timing gear cover |
39 |
398 |
29 |
|
| Vacuum pump tube x Vacuum pump assembly, No. 2 timing gear cover and cylinder block |
for bolt |
19.5 |
199 |
14 |
|
|
for union bolt |
13.5 |
138 |
10 |
|
| Front No. 1 engine mounting bracket RH x Cylinder block |
68.6 |
700 |
51 |
|
| Front No. 1 engine mounting bracket LH x Cylinder block |
68.6 |
700 |
51 |
|
CYLINDER BLOCK
| Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
| No. 1 oil nozzle sub-assembly x Cylinder block |
27 |
275 |
20 |
| Main bearing cap x Cylinder block (Quantity: 14) |
Step 1 |
103 |
1050 |
76 |
|
Step 2 |
90° |
| Main bearing cap x Cylinder block (Quantity: 15) |
18.1 |
185 |
13 |
| Connecting rod cap x Connecting rod |
Step 1 |
36.8 |
375 |
27 |
|
Step 2 |
90° |