Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
67914 1.REMOVE FRONT DOOR SCUFF PLATE LH
| *1 | Protective Tape |
Put protective tape around the front door scuff plate LH.
Using moulding remover D, detach the 4 clips and remove the front door scuff plate LH.
67913 2.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
67918A 3.REMOVE REAR DOOR SCUFF PLATE LH
| *1 | Protective Tape |
Put protective tape around the rear door scuff plate LH.
Using moulding remover D, detach the 2 clips and remove the rear door scuff plate LH.
67917A 4.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62112A 5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the cap nut.
Detach the clip and remove the cowl side trim sub-assembly LH.
62111A 6.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
62414A 7.REMOVE LOWER CENTER PILLAR GARNISH LH
Pull on both sides of the lower center pillar garnish LH and lift it up to remove it as shown in the illustration.
62413A 8.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62316C 9.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH
Remove the front door rear opening trim weatherstrip LH.
62315E 10.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62332C 11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
62331C 12.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
55356B 13.REMOVE INSTRUMENT PANEL PLATE LH
55355B 14.REMOVE INSTRUMENT PANEL PLATE RH
74617A 15.REMOVE ASSIST GRIP PLUG
Use the same procedure for all assist grip plugs.
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
Tape the screwdriver tip before use.
74603 16.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for both front assist grip sub-assemblies.
for Type A:
Remove the 2 screws and front assist grip sub-assembly.
for Type B:
Using a T25 "TORX" wrench, remove the 2 screws and front assist grip sub-assembly.
62212 17.REMOVE FRONT PILLAR GARNISH LH
Detach the claw and clip and remove the front pillar garnish LH.
62211 18.REMOVE FRONT PILLAR GARNISH RH
w/o Assist Grip:
Using a clip remover, remove the 2 clips.
Tape the clip remover tip before use.
Detach the claw and clip and remove the front pillar garnish RH.
74630E 19.REMOVE REAR ASSIST GRIP ASSEMBLY LH
for Type A:
Remove the 2 screws and rear assist grip assembly LH.
for Type B:
Using a T25 "TORX" wrench, remove the 2 screws and rear assist grip assembly LH.
74620C 20.REMOVE REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
62412 21.REMOVE CENTER PILLAR GARNISH LH
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Loosen the bolt and disconnect the front seat belt shoulder anchor.
Detach the clip, 2 guides and remove the center pillar garnish LH.
62411 22.REMOVE CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62639A 23.REMOVE QUARTER PILLAR GARNISH LH
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the rear seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Loosen the bolt and disconnect the rear seat belt shoulder anchor.
Using a clip remover, remove the 2 clips.
Tape the clip remover tip before use.
Detach the 4 clips and remove the quarter pillar garnish LH.
62638A 24.REMOVE QUARTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
74617C 25.REMOVE ASSIST GRIP PLUG
Use the same procedure for all assist grip plugs.
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
Tape the screwdriver tip before use.
74610A 26.REMOVE ASSIST GRIP SUB-ASSEMBLY
for Type A:
Remove the 2 screws and assist grip sub-assembly.
for Type B:
Using a T25 "TORX" wrench, remove the 2 screws and assist grip sub-assembly.
74620B 27.REMOVE REAR ASSIST GRIP ASSEMBLY
Use the same procedure for both front assist grip sub-assemblies.
for Type A:
Remove the 2 screws and rear assist grip assembly.
for Type B:
Using a T25 "TORX" wrench, remove the 2 screws and rear assist grip assembly.
81241 28.REMOVE NO. 1 ROOM LIGHT LENS
81240 29.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
63312A 30.REMOVE NO. 2 ROOF HEADLINING
Using a clip remover, remove the 6 clips.
Tape the clip remover tip before use.
Remove the No. 2 roof headlining from the rear door as shown in the illustration.
Make sure wrinkles do not form in the No. 2 roof headlining during removal.
Make sure that the No. 2 roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the No. 2 roof headlining or vehicle interior.
74320 31.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws and visor assembly LH.
74310 32.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348 33.REMOVE VISOR HOLDER
Use the same procedure for both visor holders.
Remove the screw.
Detach the clip and remove the visor holder.
87827 34.REMOVE INNER REAR VIEW MIRROR ABSORBER
87834 35.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER
87810 36.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
63311A 37.REMOVE NO. 1 ROOF HEADLINING
Using a clip remover, remove the 5 clips.
Tape the clip remover tip before use.
Remove the No. 1 roof headlining from the front door as shown in the illustration.
Make sure wrinkles do not form in the No. 1 roof headlining during removal.
Make sure that the No. 1 roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the No. 1 roof headlining or vehicle interior.