Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
67914 1.REMOVE FRONT DOOR SCUFF PLATE LH
Remove the 4 screws and front door scuff plate LH.
67913 2.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62112A 3.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the cap nut.
Detach the clip and remove the cowl side trim sub-assembly LH.
62111A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
62316C 5.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH
Remove the front door rear opening trim weatherstrip LH.
62315E 6.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
55356B 7.REMOVE INSTRUMENT PANEL PLATE LH
55355B 8.REMOVE INSTRUMENT PANEL PLATE RH
74617A 9.REMOVE ASSIST GRIP PLUG
Use the same procedure for all assist grip plugs.
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
Tape the screwdriver tip before use.
74603 10.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for both front assist grip sub-assemblies.
Remove the 2 screws and front assist grip sub-assembly.
62212 11.REMOVE FRONT PILLAR GARNISH LH
Detach the claw and clip and remove the front pillar garnish LH.
62211 12.REMOVE FRONT PILLAR GARNISH RH
w/o Assist Grip:
Using a clip remover, remove the 2 clips.
Tape the clip remover tip before use.
Detach the claw and clip and remove the front pillar garnish RH.
73174 13.REMOVE FRONT SEAT BELT HOLE COVER LH
Using moulding remover, detach the 2 claws and 2 guides, and remove the front seat belt hole cover LH.
73173 14.REMOVE FRONT SEAT BELT HOLE COVER RH
Use the same procedure described for the LH side.
58707A 15.REMOVE JACK HOLDER SUB-ASSEMBLY
Remove the 2 bolts and jack holder sub-assembly.
62412 16.REMOVE CENTER PILLAR GARNISH LH
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.
Tape the screwdriver tip before use.
Loosen the bolt and disconnect the front seat belt shoulder anchor.
Remove the bolt and disconnect the front seat belt anchor.
Remove the 3 clips.
Detach the 5 clips and remove the center pillar garnish LH.
62411 17.REMOVE CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
74617C 18.REMOVE ASSIST GRIP PLUG
Use the same procedure for all assist grip plugs.
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
Tape the screwdriver tip before use.
74610A 19.REMOVE ASSIST GRIP SUB-ASSEMBLY
Remove the 2 screws and assist grip sub-assembly.
74320 20.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws and visor assembly LH.
74310 21.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348 22.REMOVE VISOR HOLDER
Use the same procedure for both visor holders.
Remove the screw.
Detach the clip and remove the visor holder.
87827 23.REMOVE INNER REAR VIEW MIRROR ABSORBER
87834 24.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER
87810 25.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
81290 26.REMOVE NO. 3 ROOM LIGHT ASSEMBLY
63310 27.REMOVE ROOF HEADLINING ASSEMBLY
Using a clip remover, remove the 8 clips.
Tape the clip remover tip before use.
Remove the roof headlining assembly from the front door as shown in the illustration.
Make sure wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.