Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2014.08–2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B2797  Communication Malfunction No. 1  


DESCRIPTION

This DTC is stored when a communication error occurs between the transponder key amplifier and transponder key ECU assembly. Some possible reasons for the communication error are: 1) 2 or more ignition keys are positioned too close together, or 2) noise is occurring in the communication line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2797 Communication Malfunction No. 1 A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Harness or connector

·

Transponder key amplifier

·

Transponder key ECU assembly


Detection Enabling Condition (DTC Output Confirmation Operation)

Insert the key into the ignition key cylinder



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC No. Data List and Active Test
B2797 BCC Malfunction

WIRING DIAGRAM

B278721E10
5.479,1.146 6.104,1.802 0.625,0.656 10 false CODE 1.229,1.146 1.792,1.708 0.563,0.563 10 false CODE 1.76,1.073 1.896,1.24 0.135,0.167 10 false 4 5.188,1.073 5.365,1.24 0.177,0.167 10 false 15 4.854,1.948 5.281,2.135 0.427,0.188 10 false L30 4.854,2.115 7.115,2.635 2.26,0.521 10 false Transponder Key ECU Assembly 0.552,1.948 0.948,2.104 0.396,0.156 10 false L28 0.552,2.115 3.063,2.625 2.51,0.51 10 false Transponder Key Amplifier

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK KEY
a.
B276087

Check whether the ignition key being used is near other ignition keys as shown in the illustration. Also, check whether a key ring is in contact with the key grip.

Result:
Result Proceed to
Key is near other keys and/or key ring is in contact with key grip A
Key is not near other keys and/or key ring is not in contact with key grip B




A

2.CHECK FOR DTC

B

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)
2.CHECK FOR DTC
a.

Separate the keys from each other and/or remove the key ring.


b.

Clear the DTC.

Body Electrical > Immobiliser > Clear DTCs
50002 260

c.

Insert a key into the ignition key cylinder, and then remove it. Repeat this for all the other keys.


d.

Check that no code is output.

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2797 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)
3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the L28 transponder key amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (CODE) - L28-4 (CODE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY
a.

Using an oscilloscope, check for noise in the waveform between the terminals of the G28 transponder key amplifier connector and L30 transponder key ECU assembly connector.

B274401C07
0.438,0.833 0.802,1.125 0.365,0.292 2.958,0.906 3.344,1.208 0.385,0.302 1.25,1.083 1.469,1.354 1.469,1.354 1.75,1.354 true 3.177,1.417 3.417,1.417 3.417,1.417 3.656,1.146 true 5.833,1.271 5.979,1.271 5.979,1.271 6.125,1.063 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 3.104,0.125 3.417,0.281 0.313,0.156 10 false *b 5.688,1.177 5.958,1.344 0.271,0.167 10 false *c 0.5,0.906 0.958,1.104 0.458,0.198 10 false L28 3.01,0.979 3.469,1.177 0.458,0.198 10 false L30 1.792,1.281 2.406,1.479 0.615,0.198 10 false CODE 2.74,1.344 3.354,1.542 0.615,0.198 10 false CODE
*a Component with harness connected
(Transponder Key Amplifier)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Noise should not appear - -


Measurement Condition:
Item Content
Tester Connection L30-15 (CODE) - L28-4 (CODE)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Key inserted in ignition key cylinder


OK:

No noise is present (see illustration).



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY AMPLIFIER

NG

FIND CAUSE OF NOISE AND REMOVE IT

5.REPLACE TRANSPONDER KEY AMPLIFIER
a.

Replace the transponder key amplifier with a new or normally functioning one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY