Home › Drivetrain › R151F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM25T0E _52 Drivetrain _029903 R151F MANUAL TRANSMISSION / TRANSAXLE _0137556 OUTPUT SHAFT A

R151F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33335 7.REMOVE 1ST GEAR

a.
C315197N01
2.271,1.25 2.531,0.667 2.531,0.667 2.813,0.667 false 2.906,0.573 3.219,0.813 0.313,0.24 10 false SST

Using SST and a press, press out the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

SST
09950-00020  


Hide 33037B 8.REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR) (FOR 1ST GEAR)

a.

Remove No. 1 synchronizer ring set (for 1st gear) from the output shaft.


Hide 33348A 9.REMOVE 1ST GEAR THRUST WASHER PIN

a.

Remove the 1st gear thrust washer pin from the output shaft.


Hide 33335C 10.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.

Remove the 1st gear needle roller bearing from the output shaft.


Hide 33335B 11.REMOVE 1ST GEAR BEARING SPACER

a.

Remove the 1st gear bearing spacer from the output shaft.


Hide 33321M 12.REMOVE BEARING SHAFT SNAP RING

a.
C315198

Using 2 screwdrivers and a hammer, tap out the bearing shaft snap ring from the output shaft.

NOTICE:

Use a cloth to prevent the bearing shaft snap ring from flying off.



Hide 33332 13.REMOVE 2ND GEAR

a.
C315199N01
1.198,1.063 0.938,0.438 0.938,0.438 0.698,0.438 false 0.323,0.333 0.781,0.531 0.458,0.198 10 false SST

Using SST and a press, press off the No. 1 transmission clutch hub together with the reverse gear, No. 1 synchronizer ring set (for 2nd gear) and 2nd gear from the output shaft.

SST
09950-00020  


Hide 33332B 14.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.

Remove the 2nd gear needle roller bearing from the output shaft.


Hide 33331 15.REMOVE REVERSE GEAR

a.
C315200

Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 No. 1 synchromesh shifting key springs.

NOTICE:

Use a cloth to prevent the shifting key and the shifting key springs from popping out.



Hide 33321D 16.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.

Using a snap ring expander, remove the clutch hub set shaft snap ring from the output shaft.


Hide 33333 17.REMOVE 3RD GEAR

a.
C315201N01
0.573,0.365 0.813,0.365 0.813,0.365 1.063,0.927 false 0.188,0.271 0.542,0.479 0.354,0.208 10 false SST

Using SST and a press, press out the No. 2 transmission clutch hub together with the No. 2 transmission hub sleeve, No. 2 synchronizer ring and 3rd gear from the output shaft.

SST
09950-00020  


Hide 33333A 18.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the 3rd gear needle roller bearing from the output shaft.


Hide 33364 19.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.

Remove the No. 2 transmission hub sleeve, 3 No. 2 synchromesh shifting key springs, and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.


Hide 33348 24.INSPECT 1ST GEAR THRUST WASHER

Hide 33037B 25.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

Hide 33037B 26.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR)

Hide 27.INSPECT NO. 2 SYNCHRONIZER RING (FOR 3RD GEAR)

Hide 29.INSPECT NO. 1 TRANSMISSION CLUTCH HUB

Hide 33364 30.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

Hide 31.INSPECT NO. 2 TRANSMISSION CLUTCH HUB