Home › Drivetrain › R151F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM25T0E _52 Drivetrain _029903 R151F MANUAL TRANSMISSION / TRANSAXLE _0137556 OUTPUT SHAFT A

R151F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33364 1.INSTALL NO. 2 TRANSMISSION HUB SLEEVE

a.
C315222

Install the 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys to the No. 2 transmission clutch hub.

NOTICE:
C314953C01
0,0 0,0 false
V100135

Front Side


Be careful of the direction of the No. 2 transmission hub sleeve and that of the No. 2 transmission clutch hub.



b.

Apply gear oil to the sliding part of the No. 2 transmission hub sleeve, and install it to the No. 2 transmission clutch hub.


Hide 33333A 2.INSTALL 3RD GEAR NEEDLE ROLLER BEARING

a.
C315223

Apply gear oil to the 3rd gear needle roller bearing, and install it to the output shaft.


Hide 33333 3.INSTALL 3RD GEAR

a.
C315224

Apply gear oil to the 3rd gear, and install it to the output shaft.


Hide 33368 4.INSTALL NO. 2 SYNCHRONIZER RING (FOR 3RD GEAR) (FOR 3RD GEAR)

a.
C315225

Apply gear oil to the No. 2 synchronizer ring, and install it to the 3rd gear.


Hide 33362 5.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
C315226N01
1.854,0.594 2.542,0.594 false 2.677,0.51 3.135,0.708 0.458,0.198 10 false SST

Using SST and a press, press in the No. 2 transmission clutch hub to the output shaft.

SST
09608-06041  

NOTICE:
·

Install the hub while aligning the key groove of the hub and the shifting key position.

·

The 3rd gear should be able to rotate smoothly.




b.

Select a snap ring so that the clearance between the No. 2 transmission clutch hub and clutch hub set shaft snap ring is within the specification.

NOTICE:

Do not damage the sliding surface of the bearing.


Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Thickness
1.80 mm (0.0709 in.)
1.85 mm (0.0728 in.)
1.90 mm (0.0748 in.)
1.95 mm (0.0768 in.)
2.00 mm (0.0787 in.)
2.05 mm (0.0807 in.)
2.10 mm (0.0827 in.)



c.
C315227

Using a snap ring expander, install the clutch hub set shaft snap ring.


Hide 33332B 6.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

a.
C315228

Apply gear oil to the 2nd gear needle roller bearing, and install it to the output shaft.


Hide 33332 7.INSTALL 2ND GEAR

a.
C315229

Apply gear oil to the 2nd gear, and install it to the output shaft.


Hide 33037B 8.INSTALL SYNCHRONIZER RING SET NO.1 (FOR 2ND GEAR)

a.
C315230

Apply gear oil to the No. 1 synchronizer ring set, and install it to the 2nd gear.


Hide 33331 9.INSTALL REVERSE GEAR

a.
C315231

Using a screwdriver, install the 3 No. 1 synchromesh shifting key springs and 3 No. 1 synchromesh shifting keys to the No. 1 transmission clutch hub.


b.

Apply gear oil to the reverse gear, and install it to the No. 1 transmission clutch hub.

NOTICE:
C314954C01
0,0 0,0 false
V100135

Front Side


Be careful of the direction of the reverse gear and that of the No. 1 transmission clutch hub.



Hide 33361 10.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C315232N01
1.99,1.844 2.667,1.844 true 2.781,1.802 3.24,2 0.458,0.198 10 false SST

Using SST and a press, press in the No. 1 transmission clutch hub to the output shaft.

SST
09316-60011  (09316-00041)

NOTICE:
·

While performing the step, make sure that the No. 1 synchronizer ring key groove and No. 1 synchromesh shifting key position are aligned.

·

The 1st gear should rotate freely.




b.

Select a bearing shaft snap ring so that the thrust clearance between the No. 1 transmission clutch hub and bearing shaft snap ring is within the specification.

Standard clearance:

0.1 mm (0.0393 in.) or less


NOTICE:

Do not damage the sliding surface of the bearing.


Snap Ring Thickness:
Thickness
2.30 mm (0.0906 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)



c.
C315233

Using a brass bar and hammer, tap on the bearing shaft snap ring.


Hide 33335B 11.INSTALL 1ST GEAR BEARING SPACER

a.
C315234

Apply gear oil to the 1st gear bearing spacer, and install it to the output shaft.


Hide 33335C 12.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

a.
C315235

Apply gear oil to the 1st gear needle roller bearing, and install it to the output shaft.


Hide 33348A 13.INSTALL 1ST GEAR THRUST WASHER PIN

a.
C315236

Install the 1st gear thrust washer pin to the output shaft.


Hide 33037B 14.INSTALL NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR) (FOR 1ST GEAR)

a.
C315237

Apply gear oil to the No. 1 synchronizer ring set, and install it to the output shaft.


Hide 33335 15.INSTALL 1ST GEAR

a.
C315238

Apply gear oil to the 1st gear, and install it to the output shaft.


Hide 33348 16.INSTALL 1ST GEAR THRUST WASHER

a.
C315239

Apply gear oil to the 1st gear thrust washer, and install it to the output shaft.


Hide 33321V 17.INSTALL OUTPUT SHAFT CENTER BEARING

a.
C315240N01
2.219,1.74 2.885,1.74 true 3,1.677 3.365,1.906 0.365,0.229 10 false SST

Using SST and a press, press in a new output shaft center bearing to the output shaft.

SST
09316-60011  (09316-00031)

NOTICE:

Install the output shaft center bearing so that the snap ring groove of the bearing faces rearward.



Hide 33336 18.INSTALL 5TH GEAR

a.
C315241N01
1.844,1.74 2.469,1.74 true 2.604,1.677 3.063,1.875 0.458,0.198 10 false SST

Using SST and a press, press in the 5th gear to the output shaft.

SST
09316-60011  (09316-00031)

NOTICE:
·

Check that the 5th gear and the spline of the output shaft fit before installing the 5th gear.

·

Install the 5th gear so that the convex part of the gear faces forward.