Home › Drivetrain › R151F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT
RM25T0E _52 Drivetrain _029903 R151F MANUAL TRANSMISSION / TRANSAXLE _0137558 MANUAL TRANSMISSION UNIT A

R151F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 33321 1.INSTALL OUTPUT SHAFT

a.
C272540

Apply gear oil to the sliding part of the output shaft.


b.

Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.


Hide 33321C 2.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C272935

Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft.


Hide 33311 3.INSTALL INPUT SHAFT

a.
C315172

Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

NOTICE:
·

Install the No. 2 synchronizer ring so the No. 2 synchromesh shifting key fits into the groove of the No. 2 synchronizer ring.

·

Check that the input shaft rotates slightly.




Hide 33421 4.INSTALL COUNTER GEAR

a.
C315171

Install the counter gear to the intermediate plate.


Hide 33411P 5.INSTALL CENTER COUNTER SHAFT BEARING

a.
C272974E01
2.765,1.008 3.092,1.152 0.328,0.144 10 SST 2.687,1.094 2.627,1.094 2.627,1.094 2.462,1.326 false

Using SST and a hammer, tap in a new center counter shaft bearing to the intermediate plate.

SST
09316-60011  (09316-00011)

HINT:

Install the bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



Hide 33402 6.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C315170

Apply gear oil to each sliding part of the reverse idler gear sub-assembly and reverse idler gear shaft, and install the reverse idler gear and the reverse idler shaft to the intermediate plate.

NOTICE:

Face the groove side of the reverse idler shaft with its groove facing the rear side, and install it from the rear side.



Hide 33151 7.INSTALL REAR OUTPUT SHAFT BEARING RETAINER

a.
C315169

Insert the rear output shaft bearing retainer inserting into the groove of the reverse idler gear shaft and install it with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33349C 8.INSTALL 5TH GEAR THRUST WASHER PIN

a.
C272929

Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear.


Hide 33349 9.INSTALL 5TH GEAR THRUST WASHER

a.
C272927

Apply gear oil to the 5th gear thrust washer, and install it to the counter gear.

NOTICE:

Install the thrust washer so that its chamfer side faces forward.



Hide 33394B 10.INSTALL NO. 3 SYNCHROMESH SHIFTING KEY

a.

Apply gear oil to the sliding part of the No. 3 transmission hub sleeve, and install the No. 3 transmission hub sleeve to the countershaft 5th gear.

NOTICE:

Make sure that the No. 3 transmission hub sleeve and countershaft 5th gear are installed facing the correct direction.



b.
C248514C01
1.24,3.042 1.448,3.042 1.448,3.042 1.313,2.708 true 1.781,3.052 1.688,3.052 1.688,3.052 1.552,2.667 true 1.01,2.938 1.167,3.094 0.156,0.156 10 true *a 1.823,2.958 1.979,3.115 0.156,0.156 10 true *b
*a Cutout
*b Protrusion


Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the countershaft 5th gear as shown in the illustration.

HINT:

When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.



c.
C247403

Using a snap ring expander, install the shaft snap ring to the counter 5th gear.


Hide 33428B 11.INSTALL COUNTER 5TH GEAR BEARING

a.
C315168

Apply gear oil to the 2 pieces counter 5th gear bearing and install it to the countershaft 5th gear.


Hide 33428 12.INSTALL COUNTERSHAFT 5TH GEAR

a.
C272976

Apply gear oil to the countershaft 5th gear and No. 3 transmission hub sleeve, and install them to the counter gear.


Hide 33384A 13.INSTALL NO. 3 COUNTER SYNCHRONIZER RING

a.
C272978

Apply gear oil to the No. 3 counter synchronizer ring, and install it to the counter gear.

NOTICE:

Install the No. 3 counter synchronizer ring so that the No. 3 synchromesh shifting key fits into the groove of the No. 3 counter synchronizer ring.



Hide 33318 14.INSTALL NO. 5 GEAR SPLINE PIECE

a.
C272980E01
2.189,0.447 2.484,0.592 0.295,0.145 10 SST 2.146,0.533 1.893,0.533 false

Using SST and a press, press in the No. 5 gear spline piece to the counter gear.

SST
09316-60011  (09316-00011)

NOTICE:

Check that the gear rotates freely.



Hide 33421R 15.INSTALL REAR COUNTER GEAR SHAFT SNAP RING

a.
C315187

Select a rear counter gear shaft snap ring so that the thrust clearance between the No. 5 gear spline piece and rear counter gear shaft snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Thickness
2.85 mm (0.1122 in.)
2.90 mm (0.1142 in.)
2.95 mm (0.1161 in.)
3.00 mm (0.1181 in.)
3.05 mm (0.1201 in.)
3.10 mm (0.1220 in.)
3.15 mm (0.1240 in.)



b.
C272982

Using a brass bar and hammer, tap on the rear counter gear shaft snap ring.


Hide 33321A 18.INSTALL REAR OUTPUT SHAFT BEARING

a.
C272985E01
2.49,0.733 2.777,0.893 0.288,0.159 10 SST 2.438,0.815 2.361,0.815 2.361,0.815 2.17,1.005 false

Using SST and a press, press in the output shaft spacer and a new rear output shaft bearing to the output shaft.

SST
09309-35010  


b.

Select a shaft snap ring so that the thrust clearance between the output shaft bearing shaft and snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Thickness Thickness
2.65 mm (0.1043 in.) 3.10 mm (0.1220 in.)
2.70 mm (0.1063 in.) 3.15 mm (0.1240 in.)
2.75 mm (0.1083 in.) 3.20 mm (0.1260 in.)
2.80 mm (0.1102 in.) 3.25 mm (0.1280 in.)
2.85 mm (0.1122 in.) 3.30 mm (0.1299 in.)
2.90 mm (0.1142 in.) 3.35 mm (0.1319 in.)
2.95 mm (0.1161 in.) 3.40 mm (0.1339 in.)
3.00 mm (0.1181 in.) 3.45 mm (0.1358 in.)
3.05 mm (0.1201 in.) -



c.
C315188

Using a brass bar and hammer, tap on the rear output shaft rear bearing shaft snap ring.


Hide 33228 19.INSTALL REVERSE SHIFT ARM BRACKET

a.
C291035

Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.


b.
C291038C02
0.865,1.615 0.906,1.74 0.906,1.74 1.125,1.729 false 0.698,0.854 0.906,0.854 0.906,0.854 1.104,1.021 false 0.49,0.771 0.688,0.958 0.198,0.188 10 false *1 1.188,1.646 1.385,1.833 0.198,0.188 10 false *2
*1 Reverse Idler Gear
*2 Reverse Shift Arm


Insert the tip of the reverse shift arm into the reverse idler gear.


c.
C291034

Install the reverse shift arm bracket with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.
C291033

Install the torsion spring to the reverse shift arm bracket.

NOTICE:

Make sure that the torsion spring is securely installed to the reverse shift arm.



Hide 33211 20.INSTALL REVERSE SHIFT FORK

a.
C290803

Install the reverse shift fork to the reverse shift arm.


Hide 33241 21.INSTALL REVERSE SHIFT FORK SHAFT

a.
C314598

Install the No. 3 gear shift fork to the No. 3 transmission hub sleeve and reverse shift fork shaft to the intermediate plate from the front side.


b.
C289009

Install the straight pin to the reverse shift fork.


c.
C288251

Using a brass bar and hammer, tap on the shift fork shaft snap ring to the reverse shift fork shaft.


d.
C314599

Using a 5 mm pin punch and hammer, tap in the shift fork set slotted spring pin to the No. 3 gear shift fork.


Hide 33242 22.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
C315166

Install the No. 1 shift interlock roller to the intermediate plate.


b.
C288249

Install the No. 1 gear shift fork to the reverse gear.


c.
C288248

Install the No. 1 gear shift fork shaft to the intermediate plate from the rear side.


d.
C288247N01
1.76,0.917 1.875,0.792 false

Install a new bolt to the No. 1 gear shift fork.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288252

Using a brass bar and hammer, tap on the shift fork shaft snap ring to the No. 1 gear shift fork shaft.


Hide 33243A 23.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.
C315165C01
0.76,0.271 1.333,0.271 false 0.792,0.594 1.365,0.594 false 0.594,0.51 0.802,0.719 0.208,0.208 10 false *2 0.563,0.208 0.771,0.417 0.208,0.208 10 false *1
*1 No. 1 Shift Interlock Roller
*2 Shift Interlock Pin


Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.


b.
C288245

Install the No. 2 gear shift fork to the No. 2 transmission hub sleeve.


c.
C288244

Apply gear oil to the No. 2 gear shift fork, and install the No. 2 gear shift fork shaft to the intermediate plate from the rear side.


d.
C288243

Install a new bolt to the No. 2 gear shift fork.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288253

Using a brass bar and hammer, tap on the shift fork shaft snap ring to the No. 2 gear shift fork shaft.


Hide 33275F 24.INSTALL SHIFT DETENT BALL PLUG

a.
C288241

Install the 2 shift detent ball low side compression springs and 2 shifts detent balls to the intermediate plate.


b.
C314573C01
1.531,2.188 1.844,2.385 0.313,0.198 10 false *b 0.573,2.188 0.885,2.385 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Install the 2 shift detent ball plugs to the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, install the 2 shift detent ball plugs to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


ii.

for Type B:

Apply adhesive to 2 or 3 threads of the 2 shift detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

for Type B:

Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)



c.
C315164

Install the shift detent ball and shift detent ball low side compression spring to the intermediate plate.


d.
C314572C01
1.625,2.208 1.938,2.406 0.313,0.198 10 false *b 0.594,2.219 0.906,2.417 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Install the shift detent ball plug to the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, install the shift detent ball plug to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


ii.

for Type B:

Apply adhesive to 2 or 3 threads of the shift detent ball plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

for Type B:

Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)



Hide 33449B 25.INSTALL TRANSMISSION MAGNET

a.
C315163

Clean the transmission magnet, and install it to the intermediate plate.


Hide 33126A 26.INSTALL OIL RECEIVER SEAL

a.
C312677

Install the oil receiver seal to the No. 1 manual transmission oil separator.


Hide 33176 27.INSTALL NO. 1 MANUAL TRANSMISSION OIL SEPARATOR

a.
C312676

Install the No. 1 manual transmission oil separator with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 33111 28.INSTALL MANUAL TRANSMISSION CASE

a.
C315189C01
2.417,0.385 2.917,0.385 true 3,0.323 3.313,0.521 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.

·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) a long the sealing surface of the transmission case




b.
C315190

Using a plastic-faced hammer, install the manual transmission case by tapping the intermediate plate.


Hide 33411D 29.INSTALL FRONT NO. 1 COUNTER GEAR BEARING SNAP RING

a.
C315161

Using a snap ring expander, install the front No. 1 counter gear bearing snap ring to the manual transmission case.


Hide 33311G 30.INSTALL FRONT BEARING SHAFT SNAP RING

a.
C315160

Using a snap ring expander, install the front bearing shaft snap ring to the manual transmission case.


Hide 33131A 31.INSTALL FRONT TRANSMISSION BEARING RETAINER OIL SEAL

a.
C314207N01
0.896,2.083 1.26,2.083 1.26,2.083 1.906,1.448 true 0.51,2.01 0.875,2.219 0.365,0.208 10 false SST

Using SST and a press, tap in a new front transmission bearing retainer oil seal to the front bearing retainer.

SST
09950-60010  (09951-00520, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

11.20 to 12.20 mm (0.4410 to 0.4803 in.)



b.

Lightly apply MP grease to the lip of the front transmission bearing retainer oil seal.


Hide 33131 32.INSTALL FRONT BEARING RETAINER

a.

Remove any old FIPG material.


b.

Clean the contact surfaces of any residual FIPG material using non-residue solvent.


c.

Clean and degrease the 8 bolts and the installation holes in the transmission case.


d.
C315154C01
2.229,0.844 2.708,0.844 false 2.823,0.75 3.135,0.948 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the front bearing retainer, as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.


NOTICE:
·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.

·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) a long the sealing surface of the transmission case




e.

Apply adhesive to 2 or 3 threads of the bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent.



f.
C315191

Install the front bearing retainer to the manual transmission case with the 8 bolts.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)


Hide 33280F 33.INSTALL REVERSE RESTRICT PIN ASSEMBLY

a.
C315159

Install the reverse restrict pin assembly to the transfer adapter.


b.
C315158

Using a 5 mm pin punch and hammer, tap in the reverse restrict slotted pin to the transfer adapter.


c.
C315208

Using a T40 ''TORX'' socket wrench, install the reverse restrict pin plug to the transfer adapter.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 36111Q 34.INSTALL OIL RECEIVER PIPE

a.
C315156

Install the oil receiver pipe to the transfer adapter.


Hide 36117 35.INSTALL TRANSFER ADAPTER

a.
C315189C01
2.417,0.385 2.917,0.385 true 3,0.323 3.313,0.521 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the transfer adapter as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.

·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) a long the sealing surface of the transmission case




b.

Using a plastic-faced hammer, tap the transfer adapter it to the manual transmission case.


c.
C272765

Install the transfer adapter to the manual transmission case with the 10 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33261C 36.INSTALL SHIFT AND SELECT LEVER SHAFT

a.

Install the shift and select lever shaft and shift lever housing to the transfer adapter.


b.
C272764

Using a 5 mm pin punch and hammer, tap in the reverse restrict slotted pin to the transfer adapter.


Hide 33506F 37.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C314601C01
0.802,0.313 0.646,0.177 0.646,0.177 0.458,0.177 true 2.688,1.917 2.5,1.917 2.5,1.917 2.344,1.781 true 2.729,1.854 3.042,2.052 0.313,0.198 10 true *2 1.458,0.104 1.646,0.313 0.188,0.208 10 true *b 0.229,0.115 0.438,0.292 0.208,0.177 10 true *1 1.448,1.833 1.625,2.052 0.177,0.219 10 true *a
*1 Clamp
*2 Wire Harness Clamp Bracket
*a 75 to 120 °
*b 80 to 100 °


Install the floor shift control shift lever retainer sub-assembly, oil deflector, clamp and wire harness clamp bracket with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33280 38.INSTALL RESTRICT PIN

a.

Clean and degrease the 2 restrict pins and the installation holes in the transfer adapter.


b.

Apply adhesive to 2 or 3 threads of the restrict pins.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



c.
C272762C02
0.844,0.146 1,0.146 1,0.146 1.323,0.625 true 0.75,2 1.094,2 1.094,2 1.333,1.802 true 0.594,0.073 0.802,0.271 0.208,0.198 10 true *a 0.51,1.917 0.719,2.115 0.208,0.198 10 true *b
*a Yellow
*b Orange


Install the 2 restrict pins to the transfer adapter.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 84210 39.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C316270N01
1,1.344 1.313,1.344 1.313,1.344 1.552,1.073 true 0.698,1.281 1.156,1.479 0.458,0.198 10 true SST

Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.

SST
09817-16011  

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 31111 40.INSTALL CLUTCH HOUSING

a.

Clean the threads of the bolts and the case with non-residue solvent.


b.
C272760C01
0.195,1.093 0.346,1.244 0.151,0.151 10 *a 1.196,0.998 0.413,1.202 0.413,1.202 1.243,1.285 false
*a Precoated Bolt


Install the clutch housing to the manual transmission case with the 7 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.

Apply a few drops of adhesive to 2 or 3 threads of each of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Install the 2 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 33104 41.INSTALL DRAIN PLUG SUB-ASSEMBLY

a.

Install a new gasket and the drain plug sub-assembly to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33101A 42.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.

Install a new gasket and the manual transmission filler plug to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33019 43.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C312502

Connect the transmission breather sub-assembly to the manual transmission, and slide the clip to secure it.


b.

Connect the clamp.