Home › Engine / Hybrid System › 1GR-FE (COOLING) › RADIATOR
RM25T0E _51 Engine / Hybrid System _029895 1GR-FE COOLING _0136491 RADIATOR A

1GR-FE COOLING  RADIATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL UPPER AND LOWER RADIATOR TANK

a.
A113341C01
2.281,1 2.5,0.75 2.5,0.75 2.667,0.75 false 2.688,0.667 3,0.823 0.313,0.156 10 false *1 0.333,2.042 0.646,2.198 0.313,0.156 10 false *a 0.688,2.917 1,3.073 0.313,0.156 10 false *c 1.688,2.917 2,3.073 0.313,0.156 10 false *d 1.354,2.042 1.667,2.198 0.313,0.156 10 false *b 2.344,2.031 2.656,2.188 0.313,0.156 10 false *b 2.688,2.917 3,3.073 0.313,0.156 10 false *d
*1 O-Ring
*a CORRECT
*b INCORRECT
*c Normal
*d Twisted


Check that there are no foreign objects in the lock plate groove, and install a new O-ring. Make sure the O-ring is not twisted.

HINT:

When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.



b.

Install the upper and lower radiator tank without damaging the O-ring.


c.
A336191C01
0.969,0.646 1.177,0.458 1.177,0.458 1.354,0.458 false 1.177,1.104 1.406,0.896 1.406,0.896 1.552,0.896 false 1.396,0.354 1.604,0.542 0.208,0.188 10 false *c 1.583,0.802 1.781,0.99 0.198,0.188 10 false *d 0.271,0.229 0.469,0.427 0.198,0.198 10 false *a 2.052,0.229 2.271,0.427 0.219,0.198 10 false *b
*a CORRECT
*b INCORRECT
*c Tank
*d Lock Plate


Tab the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and upper and lower radiator tank.


Hide 2. ASSEMBLE SST

a.
A336192C01
0.646,2.927 0.646,2.563 false 1.698,2.958 1.698,2.594 true 2.375,0.771 2.563,0.469 2.563,0.469 2.74,0.469 false 3.104,1.667 3.104,1.208 3.104,1.208 2.875,1.156 true 3.031,1.677 3.229,1.875 0.198,0.198 10 false *c 0.625,1.479 0.823,1.677 0.198,0.198 10 false *a 2.771,0.365 2.969,0.563 0.198,0.198 10 false *b 0.583,2.948 0.781,3.146 0.198,0.198 10 false *d 2.438,2.896 2.635,3.094 0.198,0.198 10 false *e 1.573,2.99 1.896,3.177 0.323,0.188 10 false SST
*a Dimension B
*b Part A
*c Stopper Bolt
*d Punch Assembly
*e Overhaul Handle


Install the punch assembly to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  09231-14010  


b.

While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

10.25 mm (0.404 in.)



Hide 3.CAULK LOCK PLATE

a.
A336193C01
1.99,3.74 2.271,3.74 2.271,3.74 2.479,3.865 true 1.99,4.479 2.146,4.479 2.146,4.479 2.469,4.083 true 0.781,2.604 1.063,2.604 1.063,2.604 1.417,2.74 true 1.542,2.771 2.104,2.021 2.104,2.021 2.302,2.021 true 1.802,3.646 2.01,3.844 0.208,0.198 10 true *b 1.792,4.375 2,4.583 0.208,0.208 10 false *c 0.604,2.5 0.802,2.708 0.198,0.208 10 false *a 2.365,1.927 2.823,2.125 0.458,0.198 10 false SST 3.229,0.771 3.365,0.958 0.135,0.188 10 false 2 0.104,0.76 0.24,0.948 0.135,0.188 10 false 1 1.677,0.156 1.813,0.344 0.135,0.188 10 false 3 1.677,1.5 1.813,1.688 0.135,0.188 10 false 4 0.948,0.156 1.083,0.344 0.135,0.188 10 false 5 0.938,1.5 1.073,1.688 0.135,0.188 10 false 6 2.417,0.156 2.552,0.344 0.135,0.188 10 false 7 2.427,1.49 2.563,1.677 0.135,0.188 10 false 8
*a Stopper Plate
*b Tank
*c Lock Plate


Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.

SST
09230-01010  

NOTICE:
·
A336194C01
2.094,0.094 2.313,0.333 0.219,0.24 10 true *a 2.094,1.427 2.323,1.656 0.229,0.229 10 true *b 0.302,2.354 0.521,2.563 0.219,0.208 10 true *c
*a Port and Bracket
*b Port
*c Bracket


Do not press the protruding areas around the ports and brackets.

·
A336195

Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.




b.
A336196E01
3.083,0.708 3.24,0.906 0.156,0.198 10 false H

Check the lock plate height H after completing the caulking.

Standard plate height H:

10.25 mm (0.404 in.)


If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


Hide 16400B 4.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the radiator drain cock plug.


b.

Install the radiator drain cock plug by hand.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 5.INSPECT FOR WATER LEAK

a.
A336197E01
2.656,0.917 2.938,0.917 false 1.74,0.844 2.292,0.51 2.292,0.51 2.427,0.51 true 2.479,0.417 2.813,0.604 0.333,0.188 10 false SST 2.344,0.813 2.677,1 0.333,0.188 10 false SST

Plug the inlet and outlet ports of the radiator assembly with SST.

SST
09230-01010  


b.

Using a radiator cap tester, apply pressure to the radiator assembly.

Standard test pressure:

177 kPa (1.8 kgf/cm2, 26 psi)



c.

Submerge the radiator assembly in water.


d.
A336198C03
0.938,0.396 1.177,0.396 1.177,0.396 1.729,0.667 true 2.344,1.156 2.604,0.896 2.604,0.896 2.823,0.896 false 2.042,1.656 2.438,1.833 2.438,1.833 2.625,1.833 true 2.844,0.802 3.042,1 0.198,0.198 10 false *a 0.75,0.302 0.958,0.5 0.208,0.198 10 false *b 2.688,1.74 2.896,1.938 0.208,0.198 10 false *1
*1 O-Ring
*a Tank
*b Lock Plate


Inspect for leak.

HINT:

For radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator assembly is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator assembly in water until all air bubbles are released.



Hide 16453 6.INSTALL RADIATOR SIDE SUPPORT PLATE RH

a.

Install the radiator side support plate RH with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16454 7.INSTALL RADIATOR SIDE SUPPORT PLATE LH

a.

Install the radiator side support plate LH with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)