Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J71 Series)
RM25T0E _59 Vehicle Exterior _029942 EXTERIOR PANELS / TRIM _0147651 QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J71 Series) A

EXTERIOR PANELS / TRIM  QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J71 Series)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 76608 1.REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH

Hide 61608B 2.REMOVE REAR WHEEL OPENING EXTENSION SUB-ASSEMBLY LH

a.
B388409

Remove the 7 bolts and rear wheel opening extension sub-assembly LH.


Hide 61784 3.REMOVE REAR NO. 2 WHEEL OPENING EXTENSION PAD

a.
B388423

Remove the rear No. 2 wheel opening extension pad.


Hide 58742F 4.REMOVE REAR WHEEL EXTENSION PROTECTOR LH

a.
B388424

Remove the rear wheel extension protector LH.


Hide 61696F 5.REMOVE REAR NO. 2 WHEEL OPENING BRACKET LH

a.
B388410N02
0.438,0.479 0.646,0.729 0.208,0.25 10 false A

Remove the 2 rivets and rear No. 2 wheel extension bracket LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 2 wheel opening bracket LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 53861B 6.REMOVE REAR NO. 1 WHEEL OPENING BRACKET FRONT

a.
B388412N01
0.438,2.417 0.656,2.646 0.219,0.229 10 false A

Remove the 2 rivets and rear No. 1 wheel extension bracket.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 1 wheel opening bracket.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61693D 7.REMOVE REAR NO. 1 WHEEL OPENING BRACKET REAR

HINT:

Use the same procedure for all rear No. 1 wheel opening brackets.


a.
B388414N01
0.438,2.396 0.688,2.688 0.25,0.292 10 false A

Remove the 2 rivets and rear No. 1 wheel extension bracket.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 1 wheel opening bracket.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 53865A 8.REMOVE REAR NO. 3 WHEEL OPENING BRACKET

a.
B388416N01
0.438,0.417 0.698,0.667 0.26,0.25 10 false A

Remove the 2 rivets and rear No. 3 wheel extension bracket.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 3 wheel opening bracket.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 53872C 9.REMOVE REAR NO. 8 WHEEL OPENING BRACKET

a.
B388418N01
0.438,0.417 0.656,0.646 0.219,0.229 10 false A

Remove the 2 rivets and rear No. 8 wheel extension bracket.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 8 wheel opening bracket.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61697F 10.REMOVE REAR NO. 3 WHEEL OPENING BRACKET LH

a.
B388421N01
0.438,0.417 0.635,0.635 0.198,0.219 10 false A

Remove the 2 rivets and rear No. 3 wheel extension bracket LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 3 wheel opening bracket LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.