Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J79 Series)
RM25T0E _59 Vehicle Exterior _029942 EXTERIOR PANELS / TRIM _0147650 QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J79 Series) A

EXTERIOR PANELS / TRIM  QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J79 Series)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH and RH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 61693E 1.INSTALL REAR NO. 1 WHEEL OPENING BRACKET

a.
B388407

Install the rear No. 1 wheel opening bracket with 2 new rivets.

i.

Using an air riveter or hand riveter with a nose piece, install the rear No. 1 wheel opening bracket with 2 new rivets.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the bracket.

·

Do not tilt the riveter when installing the rivet to the bracket.

·

Do not leave any space between the rivet head and bracket.

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the bracket and door. Firmly hold together the 2 items while installing the rivet.





Hide 61683D 2.INSTALL REAR NO. 1 WHEEL OPENING BRACKET RH

a.
B388405

Install the rear No. 1 wheel opening bracket RH with 2 new rivets.

i.

Using an air riveter or hand riveter with a nose piece, install the rear No. 1 wheel opening bracket RH with 2 new rivets.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the bracket.

·

Do not tilt the riveter when installing the rivet to the bracket.

·

Do not leave any space between the rivet head and bracket.

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the bracket and door. Firmly hold together the 2 items while installing the rivet.





Hide 61684D 3.INSTALL REAR NO. 1 WHEEL OPENING BRACKET LH

HINT:

Use the same procedures described for the RH side.


Hide 58742J 4.INSTALL REAR WHEEL EXTENSION PROTECTOR LH

a.

Clean the rear wheel opening extension sub-assembly LH surface.

i.

Remove the double-sided tape from the rear wheel opening extension sub-assembly LH.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear wheel extension protector LH.

i.

Remove the peeling paper from the face of the rear wheel extension protector LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.
B388403C01
0.802,1.26 1.26,1.26 true 1.302,1.188 1.615,1.385 0.313,0.198 10 false *1
*1 Application Tape


Align the rear wheel extension protector LH as shown in the illustration and using a asqueegee, apply the rear wheek extension protector.

HINT:

Press the rear wheel extension protector LH firmly to install it.



iii.

Remove the application tape from the face of the rear wheel extension protector LH.



Hide 61783E 5.INSTALL REAR NO. 1 WHEEL OPENING EXTENSION PAD

a.

Clean the rear No. 1 wheel opening extension sub-assembly LH surface.

i.

Remove the double-sided tape from the rear No. 1 wheel opening extension sub-assembly LH.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear No. 1 wheel opening extension pad.

i.

Remove the peeling paper from the face of the rear No. 1 wheel opening extension pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.
B388451C01
2.104,0.969 2.104,0.521 2.104,0.521 2.479,0.521 false 2.51,0.438 2.792,0.729 0.281,0.292 10 false *a
*a Installation position


Install the rear No. 1 wheel opening extension pad as shown in the illustration.

HINT:

Press the rear No. 1 wheel opening extension pad firmly to install it.




Hide 61062C 6.INSTALL REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH

a.

Install 6 new clips.


b.

Attach the 6 clips to install the rear No. 1 wheel opening extension sub-assembly LH.


c.

Install the 4 bolts.


Hide 76918C 7.INSTALL REAR SIDE MUDGUARD LH

a.

Install the rear side mudguard LH with the bolt.


b.
B388398

Install the rear side mudguard LH with 2 new rivets.

i.

Using an air riveter or hand riveter with a nose piece, install the rear side mudguard LH with 2 new rivets.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the bracket.

·

Do not tilt the riveter when installing the rivet to the bracket.

·

Do not leave any space between the rivet head and bracket.

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the bracket and door. Firmly hold together the 2 items while installing the rivet.