Home › Drivetrain › H152F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT › from 2016.08
RM25T0E _52 Drivetrain _058021 H152F MANUAL TRANSMISSION / TRANSAXLE _0282328 MANUAL TRANSMISSION UNIT A

H152F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101J 1.REMOVE BREATHER PLUG

a.
C312652

Remove the 2 bolts and transmission oil baffle.


b.
C312653

Slide the 2 clips and disconnect the transmission breather hose from the floor shift control shift lever retainer sub-assembly and breather plug.


c.

Remove the breather plug from the clutch housing.


Hide 84210 2.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C363600

Widen the clamp and disconnect the wire harness from the wire harness clamp bracket as shown in the illustration.


b.

Disconnect the back-up light switch connector clamp.


c.
C212008N01
2.802,0.177 2.458,0.177 2.458,0.177 1.823,0.979 true 2.938,0.083 3.302,0.302 0.365,0.219 10 false SST

Using SST, remove the back-up light switch assembly and gasket.

SST
09817-16011  


Hide 84225A 3.REMOVE SHIFT POSITION SWITCH

C212009N01
2.135,1.083 2.406,0.302 2.406,0.302 2.677,0.302 true 2.802,0.208 3.188,0.417 0.385,0.208 10 false SST

a.

Using SST, remove the shift position switch and gasket.

SST
09817-16011  


Hide 33280 4.REMOVE REVERSE RESTRICT PIN ASSEMBLY

C212004

a.

Remove the 2 reverse restrict pin assemblies from the floor shift control shift lever retainer sub-assembly.


Hide 33111A 5.REMOVE MANUAL TRANSMISSION CASE PLUG

C312346

a.

Remove the manual transmission case plug and gasket.


Hide 33104 6.REMOVE DRAIN PLUG SUB-ASSEMBLY

C312345

a.

Remove the drain plug sub-assembly and gasket.


Hide 31111 7.REMOVE CLUTCH HOUSING

a.
C360838

Remove the 10 bolts and clutch housing.


Hide 33131 8.REMOVE FRONT BEARING RETAINER

C171381

a.

Remove the 8 bolts and front bearing retainer.


b.

Using a brass bar and a hammer, tap the side of the front bearing retainer to remove it from the transmission case.


Hide 33131A 9.REMOVE FRONT TRANSMISSION BEARING RETAINER OIL SEAL

a.
C171295C01
0.625,0.302 1.198,0.302 1.198,0.302 1.625,0.677 true 0.365,0.229 0.677,0.427 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, pry out the front transmission bearing retainer oil seal.

NOTICE:
·

Protect the front bearing retainer with a cloth to prevent it from being damaged.

·

Be careful not to damage the lip of the front transmission bearing retainer oil seal and front bearing contact surfaces.



HINT:

Tape the screwdriver tip before use.



Hide 33506F 10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C363787C02
1.052,0.135 1.281,0.135 1.281,0.135 1.438,0.49 true 0.708,1.958 0.885,1.958 0.885,1.958 1.01,1.802 true 2.271,1.573 2.698,2.021 2.698,2.021 2.885,2.021 true 0.875,0.063 1.188,0.219 0.313,0.156 10 false *2 2.948,1.958 3.26,2.115 0.313,0.156 10 false *2 0.5,1.885 0.813,2.042 0.313,0.156 10 false *1
*1 Wire Harness Clamp Bracket
*2 Wire Harness Clamp


a.

Remove the 6 bolts, wire harness clamp bracket and 2 wire harness clamps.


b.

Remove the floor shift control shift lever retainer sub-assembly and extension housing oil deflector.


Hide 33283 11.REMOVE NO. 1 REVERSE RESTRICT PIN

C313403

a.

Using a nipper, remove the slotted pin from the floor shift control shift lever retainer sub-assembly.

NOTICE:

Do not damage the floor shift control shift lever retainer sub-assembly.


HINT:

Use a piece of cloth to prevent the floor shift control shift lever retainer sub-assembly from being damaged when removing it.



b.
C171384

Remove the No. 1 reverse restrict pin from the floor shift control shift lever retainer sub-assembly.


c.
C313404

Remove the spring from the No. 1 reverse restrict pin.


Hide 33130G 12.REMOVE TRANSMISSION OIL PUMP COVER

C212018

a.

Remove the 5 bolts.


b.
C313405C02
0.583,1.615 0.75,1.615 0.75,1.615 1.604,1.042 true 0.396,1.542 0.708,1.74 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the transmission oil pump cover from the transfer adapter sub-assembly.

NOTICE:

Do not damage the transmission oil pump cover and transfer adapter.


HINT:

Use a piece of cloth to prevent the transfer adapter from being damaged when removing it



c.
C313431

Remove the 2 pins from the output shaft.


d.

Remove the O-ring from the oil pump cover.


Hide 33467A 14.REMOVE MANUAL TRANSMISSION OIL PUMP DRIVE ROTOR

a.
C171304

Remove the manual transmission oil pump drive rotor.


Hide 33468A 15.REMOVE MANUAL TRANSMISSION OIL PUMP DRIVEN ROTOR

a.
C171305

Remove the manual transmission oil pump driven rotor.


Hide 33130H 16.REMOVE TRANSMISSION OIL PUMP COVER OIL SEAL

a.
C178035C02
0.698,0.646 0.844,0.646 0.844,0.646 1.073,1.198 true 0.51,0.583 0.823,0.781 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, pry out the transmission oil pump cover oil seal.

NOTICE:

Be careful not to damage the oil pump cover.


HINT:
·

Tape the screwdriver tip before use.

·

Use a piece of cloth to prevent the transmission oil pump cover from being damaged when removing it.




Hide 33130N 17.REMOVE MANUAL TRANSMISSION OIL PUMP COVER O-RING

a.

Mount the transmission oil pump cover in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C171298

Using a 10 mm hexagon socket wrench, remove the No. 1 transmission oil pump cover plug from the transmission oil pump cover.


c.
C171306

Using a magnet hand, remove the transmission oil pump cover compression spring.


d.
C171307

Using a magnet hand, remove the transmission oil pump cover ball.


e.
C313406

Hold the hole with your finger in the position shown in the illustration, and using an air gun, blow air into the transmission oil cover gradually to raise the oil pump relief valve seat from the manual transmission oil pump cover.


f.
C171308

Using a magnet hand, remove the oil pump relief valve seat.


g.

Remove the No. 2 transmission oil pump cover O-ring from the oil pump relief valve seat.


Hide 36117 19.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY

C212017

a.

Remove the 11 bolts, No. 1 transmission case hanger and No. 2 transmission case hanger.


b.
C313407

Using a brass bar and hammer, carefully tap the transfer adapter sub-assembly.

NOTICE:

Do not drop the internal parts.


HINT:

Hold the brass bar against the rib of the transfer adapter sub-assembly.



Hide 33461 20.REMOVE REVERSE IDLER GEAR

a.
C313426

Remove the No. 2 reverse idler thrust washer and reverse idler gear.


Hide 33402A 22.REMOVE REVERSE IDLER GEAR BUSH OR BEARING

a.
C313428

Remove the reverse idler gear bush or bearing.


Hide 33451 23.REMOVE REVERSE IDLER GEAR SHAFT

a.
C313429

Remove the reverse idler thrust washer from the reverse idler gear shaft.


b.

Remove the reverse idler gear shaft woodruff key and reverse idler gear shaft from the transmission intermediate plate.


c.

Remove the reverse idler gear shaft woodruff key from the reverse idler gear shaft.


Hide 25.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

Hide 33408 26.REMOVE MANUAL TRANSMISSION OIL STRAINER SUB-ASSEMBLY

a.
C313432

Remove the 2 bolts and manual transmission oil strainer sub-assembly from the transfer adapter sub-assembly.


b.

Remove the O-ring from the manual transmission oil strainer sub-assembly.


Hide 33449B 27.REMOVE TRANSMISSION MAGNET

C171351

a.

Remove the transmission magnet.


Hide 33112E 28.REMOVE TRANSFER ADAPTER WITH HEAD STRAIGHT SCREW PLUG

a.
C313416

Using a T40 "TORX" socket wrench, remove the transfer adapter with head straight screw plug.


Hide 33261C 29.REMOVE SHIFT AND SELECT LEVER SHAFT

C313414

a.

Using a pin punch and hammer, drive out the slotted spring pin from the shift lever housing.

NOTICE:

Using a magnet hand as shown in the illustration, do not drop the slotted pin inside.



b.
C313415

Using pliers, move the shift and select lever shaft to the rear side and remove the shift lever housing from the shift and select lever shaft.

NOTICE:

Do not damage the shift and select lever shaft.


HINT:

Use a piece of cloth to prevent the shift and select lever shaft from being damaged when moving it.



c.

Remove the shift and select lever shaft from the transmission intermediate plate.


Hide 33111 30.REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY

C171195

a.

Using a snap ring expander, remove the 2 snap rings from the input shaft and counter gear.


b.
C171197

Using a brass bar and hammer, tap the manual transmission case sub-assembly to remove it from the transmission intermediate plate.

HINT:

Hold the brass bar against the rib of the manual transmission case sub-assembly.



Hide 33124C 31.REMOVE NO. 1 OIL RECEIVER PIPE

C313433

a.

Remove the 2 bolts and No. 1 oil receiver pipe from the transmission case sub-assembly.


Hide 33125B 32.REMOVE MANUAL TRANSMISSION CASE RECEIVER

a.

Mount the transmission intermediate plate in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C171355

Remove the 3 bolts and manual transmission case receiver from the intermediate plate.


Hide 33275F 33.REMOVE SHIFT DETENT BALL PLUG

C171201

a.

Using a T40 "TORX" socket wrench, remove the 4 shift detent ball plugs.


b.

Using a magnet hand, remove the 4 shift detent ball springs and 4 shift detent balls.


Hide 33244B 34.REMOVE SHIFT FORK SHAFT SNAP RING

C313965C02
2.438,0.385 1.865,0.271 1.865,0.271 2.594,0.167 true 1.677,0.208 1.99,0.406 0.313,0.198 10 false *a
*a Protective Tape


a.

Using 2 screwdrivers and a hammer, tap out the 4 shift fork shaft snap rings.

NOTICE:
·

Use a piece of cloth to prevent the shift fork shaft snap ring from flying off.

·

Do not damage the No. 3 shift fork shaft and No. 4 gear shift fork shaft.



HINT:

Tape the screwdriver tip before use.



Hide 33211 35.REMOVE REVERSE SHIFT FORK

C313417

a.

Move the No. 3 gear shift fork to the position shown in the illustration.


b.
C171203

Remove the bolt from the No. 4 gear shift fork shaft.


c.
C171204

While pulling the No. 4 gear shift fork shaft to the rear side, remove the ball from the reverse shift head.


d.

While supporting the reverse shift fork, remove the No. 4 gear shift fork shaft from the transmission intermediate plate and reverse shift fork.


e.

Remove the reverse shift fork from the output shaft.


Hide 33214G 37.REMOVE NO. 3 GEAR SHIFT FORK

C313440C02
0.406,1.656 0.51,1.656 0.51,1.656 0.688,1.323 true 0.229,1.604 0.542,1.76 0.313,0.156 10 false *1
*1 Ball


a.

Using a magnet hand, remove the ball.


b.
C171216

Remove the bolt and while supporting the No. 3 gear shift fork, pull out the No. 3 gear shift fork shaft from the rear side of the No. 3 gear shift fork to remove the No. 3 gear shift fork from the output shaft.


c.

Remove the reverse shift head from the No. 3 gear shift fork shaft.


d.

Remove the No. 3 gear shift fork shaft from the transmission intermediate plate.

NOTICE:

Do not drop the interlock pin.



e.
C171357

Remove the interlock pin from the No. 3 gear shift fork shaft.


Hide 33212A 39.REMOVE NO. 1 GEAR SHIFT FORK

C313441C02
0.354,0.917 0.708,0.917 true 0.188,0.865 0.5,1.063 0.313,0.198 10 false *1
*1 Interlock Pin


a.

Using a magnet hand, remove the interlock pin.


b.
C310025

Remove the bolt and while supporting the No. 1 gear shift fork, remove the No. 1 gear shift fork shaft from the transmission intermediate plate and No. 1 gear shift fork.

NOTICE:

Do not drop the interlock pin.



c.

Remove the No. 1 gear shift fork.


d.
C313969

Remove the interlock pin from the No. 1 gear shift fork shaft.


Hide 33213G 41.REMOVE NO. 2 GEAR SHIFT FORK

C171219C02
0.594,0.583 0.833,0.583 true 0.896,0.521 1.208,0.677 0.313,0.156 10 false *1
*1 Interlock Pin


a.

Using a magnet hand, remove the interlock pin.


b.
C171220

Remove the bolt and while supporting the No. 2 gear shift fork, pull out the No. 2 gear shift fork shaft from the front side of the transmission intermediate plate and remove it together with the No. 2 gear shift fork from the output shaft.


c.

Remove the No. 2 gear shift fork from the No. 2 gear shift fork shaft.


Hide 33393A 45.REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

C313966C02
1.792,1.292 2.302,1.115 2.302,1.115 1.885,1.344 true 2.344,1.021 2.656,1.219 0.313,0.198 10 false *a
*a Protective Tape


a.

Using 2 screwdrivers and a hammer, tap out the No. 3 transmission clutch hub shaft snap ring.

NOTICE:
·

Do not damage the output shaft.

·

Use a piece of cloth to prevent the snap ring from flying off.



HINT:

Tape the screwdriver tip before use.



Hide 33363 46.REMOVE NO. 1 TRANSMISSION HUB SLEEVE

a.
C313420

Remove the No. 1 transmission hub sleeve from the No. 4 transmission clutch hub.


Hide 33331 47.REMOVE REVERSE GEAR

C313418C02
1.281,0.583 1.469,0.208 1.469,0.208 1.625,0.208 true 2.115,1.948 2.427,2.104 0.313,0.156 10 false *a 0.115,1.646 0.427,1.802 0.313,0.156 10 false *b 1.698,0.146 2.156,0.344 0.458,0.198 10 false SST
*a Turn
*b Hold


a.

Using SST, remove the reverse gear, reverse synchronizer ring set and No. 4 transmission clutch hub from the output shaft.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04010, 09954-04020, 09955-04021, 09957-04010, 09958-04011)
09950-60010  (09951-00300)


Hide 33352B 48.REMOVE NO. 4 TRANSMISSION CLUTCH HUB

C313436

a.

Remove the No. 4 transmission clutch hub from the reverse gear.


b.
C313419C02
2.563,1.344 2.49,1.542 2.49,1.542 2.375,1.542 true 2.573,0.563 2.5,0.76 2.5,0.76 2.385,0.76 true 1.073,0.51 0.979,0.229 0.979,0.229 0.865,0.229 true 2.229,0.677 2.542,0.875 0.313,0.198 10 false *a 2.208,1.469 2.521,1.667 0.313,0.198 10 false *a 0.698,0.146 1.01,0.344 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the 3 shifting keys and 3 springs from the No. 4 transmission clutch hub.

NOTICE:
·

Do not drop the shifting key.

·

Do not damage the No. 4 transmission clutch hub and spring.



HINT:

Push down the spring as shown in the illustration and remove the shifting key.



Hide 33049 49.REMOVE REVERSE SYNCHRONIZER RING SET

a.
C313422

Remove the reverse synchronizer ring set from the reverse gear.


Hide 33049 50.INSPECT REVERSE SYNCHRONIZER RING SET

Hide 33331A 52.REMOVE REVERSE GEAR BEARING

a.
C313423

Remove the reverse gear bearing.


Hide 33151 53.REMOVE OUTPUT SHAFT REAR BEARING RETAINER

C313964

a.

Remove the 4 bolts and output shaft rear bearing retainer.


Hide 33421 54.REMOVE COUNTER GEAR

C174896

a.

Using a snap ring expander, remove the rear counter gear shaft snap ring.


b.
C313437C02
2.271,2.24 2.563,2.031 2.563,2.031 2.729,2.031 true 3.073,2.802 3.385,2.958 0.313,0.156 10 false *a 1.385,3.115 1.698,3.271 0.313,0.156 10 false *b 2.792,1.969 3.25,2.167 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the counter shaft center bearing (outer race).

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04011, 09957-04010, 09958-04011)
09950-60010  (09951-00300)

NOTICE:

Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.



c.
C313967C02
2.167,1.281 2.604,1.604 2.604,1.604 2.792,1.604 true 2.833,1.521 3.146,1.677 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, detach the 2 locations of the center counter shaft bearing and remove the center counter shaft bearing from the counter gear.

NOTICE:
·

Do not damage the center counter shaft bearing.

·

Do not damage the counter gear.

·

Support the counter gear by hand so that it does not fall.




d.

Remove the counter gear.

NOTICE:

Do not drop the input shaft.



Hide 33311 55.REMOVE INPUT SHAFT

C171362

a.

Remove the input shaft from the output shaft.

NOTICE:

Do not drop the input shaft bearing and No. 2 synchronizer ring.



Hide 33368 57.REMOVE NO. 2 SYNCHRONIZER RING

a.
C184150

Remove the No. 2 synchronizer ring from the input shaft.

NOTICE:

Do not drop the input shaft bearing.



Hide 33311D 58.REMOVE INPUT SHAFT BEARING

a.
C171242

Remove the 12 input shaft bearings.


Hide 33321B 59.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

C314122

a.

Using a snap ring expander, remove the output shaft bearing shaft snap ring.


Hide 60.REMOVE OUTPUT SHAFT ASSEMBLY

C314123

a.

Remove the output shaft assembly from the intermediate plate by pulling on the output shaft assembly and tapping on the intermediate plate with a plastic-faced hammer.


Hide 33112C 61.REMOVE TRANSFER ADAPTER STRAIGHT PIN

NOTICE:

It is not necessary to remove the transfer adapter straight pin unless it is being replaced.


C214495

a.

Remove the 4 transfer adapter straight pins from the transfer adapter sub-assembly.


b.
C310030

Remove the 4 transfer adapter straight pins from the transmission case sub-assembly.


c.
C310031

Remove the 4 transfer adapter straight pins from the transmission intermediate plate.