ENGINE CONTROL SYSTEM
| *1 | ECM | *2 | Atmospheric Pressure Sensor |
| *3 | Accelerator Pedal Position Sensor | *4 | Ignition Switch Signal |
| *5 | Starter Signal | *6 | Vehicle Speed Signal |
| *7 | Battery Voltage | *8 | DLC3 |
| *9 | Other Signal | *10 | Stop Light Switch |
| *11 | Generator | *12 | No. 2 Glow Relay |
| *13 | No. 1 Glow Relay | *14 | No. 1 EDU Relay |
| *15 | No. 2 EDU Relay | *16 | No. 1 Injector Driver |
| *17 | No. 2 Injector Driver | - | - |
| *1 | Fuel Supply Pump | *2 | Fuel Tank |
| *3 | Suction Control Valve | *4 | Fuel Temperature Sensor |
| *5 | Fuel Pressure Sensor | *6 | Common Rail RH |
| *7 | Pressure Discharge Valve | *8 | Common Rail LH |
| *9 | Intercooler | *10 | Intake Air Temperature Sensor |
| *11 | Diesel Throttle Body (for Bank 1) | *12 | Diesel Throttle Body (for Bank 2) |
| *13 | Manifold Absolute Pressure Sensor | *14 | Electric EGR Control Valve Assembly |
| *15 | Glow Plug | *16 | Camshaft Position Sensor |
| *17 | EGR Cooler | *18 | Fuel Injector |
| *19 | Engine Coolant Temperature Sensor | *20 | Mass Air Flow Meter |
| *21 | Crankshaft Position Sensor | *22 | Turbocharger |
| *23 | Vacuum Regulating Valve | *24 | Exhaust Fuel Addition Injector Assembly |
| *25 | Exhaust Gas Temperature Sensor | *26 | No. 2 Exhaust Gas Temperature Sensor |
| *27 | No. 3 Exhaust Gas Temperature Sensor | *28 | Air Fuel Ratio Sensor |
| *29 | Differential Pressure Sensor Assembly | *30 | Vacuum Switching Valve |
| *31 | No. 2 EGR Valve | - | - |
DIESEL PARTICULATE FILTER SYSTEM DESCRIPTION
The diesel particulate filter system comprehensively regulates engine control (consists of a catalytic system and a fuel injection system) and purifies the particulate matter (PM) of diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM with a catalytic converter using the Diesel Particulate Filter (DPF). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to maintain a proper catalyst temperature for PM forced regeneration.
DPF components:
| Component | |
|---|---|
| Front exhaust pipe assembly (DPF catalytic converter) |
Reduces HC, CO and PM. |
| Exhaust fuel addition injector assembly | Adds fuel into the exhaust port in order to raise catalyst temperature for PM forced regeneration. |
| Exhaust gas temperature sensor | Used for estimating the DPF catalytic converter temperature and adjusting fuel addition by ECM while PM forced regeneration is performed. Also, this sensor detects the DPF catalytic converter temperature to prevent the catalytic converter temperature from rising too high. |
| Differential pressure sensor assembly | Detects the volume of PM deposits and any incorrect vacuum hose arrangement on the DPF catalytic converter. |
| Air fuel ratio sensor | Used for controlling the air fuel ratio. By controlling the air fuel ratio, combustion control and PM forced regeneration are properly regulated. |
Diagnostic Trouble Codes (DTCs) table for DPF:
This table indicates typical DTC combinations for each malfunction occurrence.
| Trouble Area | Malfunction | DTC No. |
|---|---|---|
| Front exhaust pipe assembly (DPF catalytic converter) |
Deteriorated or clogged | P062F, P200C*, P200E*, P2428*, P244B*, P244C*, P2458*, P2463* |
| Exhaust Fuel Addition Injector Assembly | Stuck open | P20CF |
| Stuck closed | P244C, P2458* | |
| Low fuel addition volume | P244B*, P244C, P2458*, P2463 | |
| Open in exhaust fuel addition injector circuit | P20CD, P244C, P2458* | |
| Short in exhaust fuel addition injector circuit | P20CF, P20CD, P244C, P2458* | |
| Open or short in exhaust fuel addition injector circuit | P200C*, P200E*, P20CD, P20CF*, P2428*, P244C*, P2458* | |
| Exhaust gas temperature sensor | Open in exhaust gas temperature sensor circuit | P0545, P0546, P200C*, P200E*, P2428*, P2032, P2033, P2084, P242B, P242C, P242D, P244C*, P2458* |
| Short in exhaust gas temperature sensor circuit | P0545, P0546, P200C*, P200E*, P2428*, P2032, P2033, P2084, P242B, P242C, P242D, P244C*, P2458* | |
| Exhaust gas temperature sensor | P0545, P0546, P200C*, P200E*, P2428*, P2032, P2033, P2084, P242B, P242C, P242D, P244C*, P2458* | |
| Differential Pressure Sensor Assembly | Open in differential pressure sensor circuit | P244C* P2454, P2455, P2458*, P2463* |
| Short in differential pressure sensor circuit | P244C*, P2454, P2455, P2458*, P2463* | |
| Differential pressure sensor | P244C*, P2454, P2455, P2458*, P2463* | |
| Differential pressure sensor clogged | P244C*, P2453, P2458*, P2463* | |
| Incorrect vacuum hose arrangement of differential pressure sensor | P244C*, P2453, P2458*, P2463* | |
| Air fuel ratio sensor | Open or short in air fuel ratio sensor or heater circuit | P0031, P0032, P2238, P2239, P2252, P2253, P244B*, P2463* |
| Air fuel ratio sensor | P0031, P0032, P2195, P2238, P2239, P2252, P2253, P244B*, P2463* | |
| Exhaust gas leaks | Exhaust gas leaks | P244C*, P2458* |
| Fuel leaks | Fuel leaks in fuel addition injector | P200C*, P200E*, P20CF*, P2428*, P244B*, P2458*, P244C*, P2463* |
| Fuel supply pump assembly | Correct fuel pressure cannot be fed to exhaust fuel addition injector | P244B*, P244C*, P2458*, P2463* |
*: There may be no DTC output depending on the condition of the malfunction.
Diagnostics trouble code description for DPF:
| DTC No. | Description |
|---|---|
| P0031 | Open in air fuel ratio sensor heater control circuit (Low output) |
| P0032 | Short in air fuel ratio sensor or heater circuit (High output) |
| P0545 | Open or short in exhaust gas temperature sensor circuit (B1S1) (Low output) |
| P0546 | Open or short in exhaust gas temperature sensor circuit (B1S1) (High output) |
| P200C | DPF catalytic converter abnormally high exhaust gas temperature |
| P200E | Catalyst system temperature too high bank 1 |
| P2032 | Open or short in exhaust gas temperature sensor circuit (B1S2) (Low output) |
| P2033 | Open or short in exhaust gas temperature sensor circuit (B1S2) (High output) |
| P2084 | Exhaust gas temperature sensor circuit range/performance (B1S2) |
| P20CD | Open in exhaust fuel addition injector assembly circuit |
| P20CF | Exhaust fuel addition injector assembly stuck open |
| P2195 | Air fuel ratio sensor stuck lean |
| P2237 | Air fuel ratio sensor pumping current circuit/open |
| P2238 | Open or short in air fuel ratio sensor or heater circuit (Low output) |
| P2239 | Open or short in air fuel ratio sensor or heater circuit (High output) |
| P2252 | Open or short in air fuel ratio sensor or heater circuit (Low output) |
| P2253 | Open or short in air fuel ratio sensor or heater circuit (High output) |
| P242B | Exhaust gas temperature sensor circuit range / performance (B1S3) |
| P242C | Open or short in exhaust gas temperature sensor circuit (B1S3) (Low output) |
| P242D | Open or short in exhaust gas temperature sensor circuit (B1S3) (High output) |
| P244B | DPF catalytic converter excessive differential pressure (High input) |
| P244C | Exhaust temperature too low for particulate filter regeneration bank 1 |
| P2428 | Exhaust Gas Temperature Too High Bank 1 |
| P2453 | Differential pressure sensor is clogged or has incorrect vacuum hose arrangement |
| P2454 | Open or short in differential pressure sensor circuit (Low output) |
| P2455 | Open or short in differential pressure sensor circuit (High output) |
| P2458 | Diesel particulate filter regeneration duration |
| P2463 | DPF catalytic converter soot deposition |
COMMON RAIL SYSTEM DESCRIPTION
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail assembly, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM, using the injector driver, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail assembly using the fuel pressure sensor. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
The common rail system allows a multi-stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.
The system also performs "after-injection", which burns off fuel that was added during "pilot-injection" and "main-injection" and remained unburned, to increase the exhaust temperature for the DPF.
| *1 | Sensors | *2 | ECM |
| *3 | No. 1 Injector Driver | *4 | No. 2 Injector Driver |
| *5 | Common Rail (for Bank 1) | *6 | Fuel Pressure Sensor |
| *7 | Fuel Temperature Sensor | *8 | Suction Control Valve |
| *9 | Fuel Supply Pump | *10 | Exhaust Fuel Addition Injector Assembly |
| *11 | Fuel Injector | *12 | Pressure Limiter |
| *13 | Common Rail (for Bank 2) | *14 | Pressure Discharge Valve |
| *15 | Fuel Filter | *16 | Fuel Tank |
| *17 | High Pressure Fuel | *18 | Return Fuel |
| *19 | Suction Fuel | - | - |
If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing an fuel injector, etc., engine startability may deteriorate.
| Component | Description |
|---|---|
| Common rail | Stores high-pressure fuel produced by fuel supply pump |
| Fuel supply pump |
·
Operated by crankshaft.
·
Supplies high-pressure fuel to common rail. |
| Fuel injector | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor | Monitors internal fuel pressure of common rail and sends signals to ECM |
| Pressure discharge valve | Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high. |
| Suction control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
| Check valve | Keeps pressure that discharges from injector |
This table indicates typical DTCs for each malfunction occurrence.
| Component | Trouble Area | DTC No. |
|---|---|---|
| Fuel injector | Open or short in injector circuit | P0093*, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P062D, P062E |
| Stuck open | P0093 | |
| Stuck closed | P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308 | |
| Fuel pressure sensor | Open or short in fuel pressure sensor circuit or pressure sensor output fixed | P0087, P0190, P0192, P0193 |
| Pressure discharge valve | Open or short in pressure discharge valve circuit | P0088*, P0093*, P1229*, P1271, P1272 |
| Stuck open | P0093 | |
| Stuck closed | P0088*, P1272 | |
| Suction control valve | Open or short in suction control valve circuit | P0088*, P0627, P1229 |
| Stuck open | P0088*, P1229 | |
| Injector driver (EDU) | Faulty EDU | P0093*, P0201*, P0202*, P0203*, P0204*, P0205*, P0206*, P0207*, P0208*, P062D*, P062E*, P1271*, P1272* |
| Common rail system (Fuel system) | Fuel leaks in high-pressure areas | P0093 |
*: There may be no DTC output depending on the condition of the malfunction.
| DTC No. | Description |
|---|---|
| P0087 | Fuel pressure sensor output does not change |
| P0088 | Internal fuel pressure too high (250000 kPa [2550 kgf/cm2, 36250 psi] or more) |
| P0093 | Fuel leaks in high-pressure areas |
| P0190 | Open or short in fuel pressure sensor circuit (Low or high output) |
| P0192 | Open or short in fuel pressure sensor circuit (Low output) |
| P0193 | Open or short in fuel pressure sensor circuit (High output) |
| P0201 to P0208 | Open or short in No. 1 to No. 8 injector circuit |
| P0301 to P0308 | Cylinder 1 to 8 misfire detected |
| P0627 | Open or short in suction control valve circuit |
| P062D | Open or short in No. 1 injector driver or injector circuit |
| P062E | Open or short in No. 2 injector driver or injector circuit |
| P1229 | Fuel over-feed |
| P1271 | Open or short in pressure discharge valve circuit |
| P1272 | Pressure discharge valve stuck close |
FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
Due to the rotation of the inner cam (eccentric cam), the outer cam pushes plunger A upward as illustrated below. The force of the spring pulls plunger B and C. As a result, plunger B and C draw fuel in, and plunger A pumps fuel at the same time.
SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION
The ECM controls the suction control valve operation to regulate the fuel volume that is pumped by the fuel supply pump to the common rail. This control is performed to adjust the internal fuel pressure of the common rail to the targeted injection pressure.
Small opening of the suction control valve:
When the opening of the suction control valve is small, the fuel suction path is kept narrow. Therefore the transferable fuel volume is reduced (*A).
The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum (*B).
Pumping will start when the fuel pressure becomes higher than the common rail pressure (*C).
Large opening of the suction control valve:
When the opening of the suction control valve is large, the fuel suction path is kept wide. Therefore the transferable fuel volume is increased (*D).
If the plunger stroke is full, the suction volume becomes large because of the wide path (*E).
Pumping will start when the fuel pressure becomes higher than the common rail pressure (*F).