Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) D

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY AND ELECTRIC EGR CONTROL VALVE ASSEMBLY


HINT:

When the diesel throttle body assembly or electric EGR control valve assembly is replaced, perform initialization.


a.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.



CATALYST RECORD OF DPF THERMAL DETERIORATION CLEAR FUNCTION


HINT:

When the front exhaust pipe assembly (DPF catalytic converter) is replaced, the catalyst record of thermal deterioration stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.
A375358

Enter the menu options in this order: Engine and ECT / Utility / Catalyst Record Clear.

Powertrain > Engine and ECT > Utility
Tester Display
Catalyst Record Clear
50005 234 178

e.

Press "Next".


f.
A375359

Press "Exit".



FUEL SUPPLY PUMP INITIALIZATION PROCEDURE


HINT:

After replacing the fuel supply pump and/or the ECM:

·

If the engine is defective or stalls immediately after startup, the ECM's learned values must be initialized. The engine can be initialized through the GTS or by connecting the DLC3 terminals.

·

If the engine starts normally, initialization is not necessary. Perform the step "idle the engine" procedure below only.



a.
A280985

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Supply Pump Initialization.

Powertrain > Engine and ECT > Utility
Tester Display
Supply Pump Initialization
50005 234 163

e.

Press "Next".


f.
A280986

Press "Next".


g.
A280987

Press "Exit".


h.

Start the engine to check if the initialization is complete. If the engine cannot be started, repeat the initialization procedures from the beginning.


i.

Idle the engine for at least 1 minute under the following conditions:

·

The engine coolant temperature is 60°C (140°F) or more.

·

The fuel temperature is 20°C (68°F) or more.


NOTICE:

Do not race the engine immediately after starting the engine. After warming up the engine, racing the engine is acceptable.


HINT:
·

The engine coolant temperature can be estimated by touching the outlet hose.

·

The fuel temperature can be estimated by using the ambient temperature as a substitute.

·

If the engine coolant temperature is difficult to estimate, use the GTS and enter the following menus: Engine and ECT / Data List / Coolant Temp.




j.

Initialization is complete.



CRANK TIME COMPENSATION RESET FUNCTION


·

This procedure uses the GTS to perform "Crank Time Compensation Reset".

·

When replacing the timing rotor (engine assembly), perform "Crank Time Compensation Reset".


HINT:
·
A204035

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Crank Time Compensation Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Crank Time Compensation Reset
50005 234 237

e.
A280989

When the first screen is displayed, check the vehicle condition and push "Next".


f.
A280984

When the screen indicating reset completion is displayed, push "Exit".



A/F SENSOR COMPENSATION RESET FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Compensation Reset".

·

When replacing the air fuel ratio sensor, replace the sensor and then perform "A/F Sensor Compensation Reset".


HINT:
·
A204038

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / A/F Sensor Compensation Reset.

Powertrain > Engine and ECT > Utility
Tester Display
A/F Sensor Compensation Reset
50005 234 238

e.
A320567

When the first screen is displayed, check the vehicle condition and push "Next".


f.
A320568

When the screen indicating reset completion is displayed, push "Exit".