Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK EDU (POWER SOURCE)
a.
A204910C24
0.385,0.823 0.792,1.083 0.406,0.26 0.396,1.188 0.802,1.448 0.406,0.26 0.896,1.719 1.396,1.458 true 1,0.49 1.427,0.948 true 0.688,1.656 0.979,1.875 0.292,0.219 10 false +B 0.677,0.385 1.063,0.604 0.385,0.219 10 false GND 0.135,0.135 0.313,0.292 0.177,0.156 10 false *a 0.417,0.875 0.99,1.042 0.573,0.167 10 false C124 0.427,1.229 0.99,1.417 0.563,0.188 10 false C127 0.844,0.729 1.229,0.896 0.385,0.167 10 false *A 0.854,1.104 1.24,1.271 0.385,0.167 10 false *B
*A for Bank 1 (No. 1 Injector Driver (EDU))
*B for Bank 2 (No. 2 Injector Driver (EDU))
*a Front view of wire harness connector
(to EDU)


Disconnect the No. 1 injector driver (EDU) connectors.


b.

Disconnect the No. 2 injector driver (EDU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard voltage (No. 1):
Tester Connection Switch Condition Specified Condition
C124-3 (+B) - C124-1 (GND) Ignition switch ON 11 to 14 V


Standard voltage (No. 2):
Tester Connection Switch Condition Specified Condition
C127-3 (+B) - C127-1 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT EDU RELAY (EDU1 AND EDU2)
2.INSPECT EDU RELAY (EDU1 AND EDU2)
a.

Inspect the EDU1 relay and EDU2 relay.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EDU - EDU RELAY, EDU RELAY - ECM)

NG

REPLACE EDU RELAY (EDU 1 OR EDU 2)

3.CHECK HARNESS AND CONNECTOR (EDU - EDU RELAY, EDU RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 injector driver (EDU) connector.


c.

Disconnect the No. 2 injector driver (EDU) connectors.


d.

Remove the EDU1 relay from the engine room relay block assembly.


e.

Remove the EDU2 relay from the engine room relay block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance (No. 1):
Tester Connection Condition Specified Condition
C124-3 (+B) - EDU1 relay terminal 5 Always Below 1 Ω
A29-45 (IREL) - EDU1 relay terminal 2 Always Below 1 Ω
C124-3 (+B) or EDU1 relay terminal 5 - Body ground Always 10 kΩ or higher
A29-45 (IREL) or EDU1 relay terminal 2 - Body ground Always 10 kΩ or higher


Standard resistance (No. 2):
Tester Connection Condition Specified Condition
C127-3 (+B) - EDU2 relay terminal 5 Always Below 1 Ω
EDU2 relay terminal 3 - Battery positive (+) terminal Always Below 1 Ω
C127-3 (+B) or EDU2 relay terminal 5 - Body ground Always 10 kΩ or higher
EDU2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (EDI1 RELAY AND EDU2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (EDI1 RELAY AND EDU2 RELAY)
a.
A394579C01
0.135,0.083 0.448,0.281 0.313,0.198 10 false *1 0.646,2.906 0.958,3.104 0.313,0.198 10 false *2 0.615,1.573 0.927,1.771 0.313,0.198 10 false *3
*1 Engine Room Relay Block Assembly
*2 EDU1 Relay
*3 EDU2 Relay


Remove the EDU1 and EDU2 relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
EDU1 relay terminal 3 - Bodyground Always 11 to 14 V
EDU2 relay terminal 3 - Bodyground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR