Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (w/ VSC) › 2016.08–2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0282728 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 4.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C362109C01
1.833,1.083 2.5,0.333 2.5,0.333 2.833,0.333 true 1.729,1.188 1.083,0.333 1.083,0.333 0.5,0.333 true 0.5,0.75 1.167,0.75 1.167,0.75 1.625,1.281 true 0.5,1.083 1.167,1.083 1.167,1.083 1.521,1.396 true 2.396,1.375 2.667,1.583 2.667,1.583 3,1.583 true 2.083,1.698 2.417,3.167 2.417,3.167 2.75,3.167 true 2.833,3.083 3.146,3.281 0.313,0.198 10 false *e 2.917,0.25 3.229,0.448 0.313,0.198 10 false *d 0.292,0.979 0.604,1.177 0.313,0.198 10 false *a 0.302,0.667 0.615,0.865 0.313,0.198 10 false *b 0.302,0.229 0.615,0.427 0.313,0.198 10 false *c 3.083,1.5 3.396,1.698 0.313,0.198 10 false *f
*a To Front Wheel Cylinder RH
*b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder RH
*d To Rear Wheel Cylinder LH
*e From 1st Chamber of Brake Master Cylinder Sub-assembly
*f From 2nd Chamber of Brake Master Cylinder Sub-assembly


Place tags or marks to identify the installation locations of each brake line.


b.
C362110C01
0,0 0,0 false
V113147

Lock Lever Released
V113148

Connector Disconnected


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Detach the 3 clamps from the brake actuator bracket assembly.


d.
C362112

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


e.
C362113

Remove the 3 nuts and brake actuator with bracket.

NOTICE:

Do not damage the brake lines.



Hide 44510 5.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C362114

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket.


Hide 6.REMOVE BRAKE ACTUATOR CASE COLLAR

a.
C362115

Remove the 3 brake actuator case collars from the 3 brake actuator bracket cushions.


Hide 44547B 7.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C362116

Remove the 3 brake actuator bracket cushions from the brake actuator bracket.