Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (w/ VSC) › 2016.08–2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0282728 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  INSTALLATION  


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.
C362116

Install the 3 brake actuator bracket cushions to the brake actuator bracket.


Hide 2.INSTALL BRAKE ACTUATOR CASE COLLAR

a.
C362115

Install the 3 brake actuator case collars to the 3 brake actuator bracket cushions.


Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C362114N01
1.813,0.906 1.969,1.104 0.156,0.198 10 false A 2.802,1.427 2.958,1.625 0.156,0.198 10 false B 2.448,2.031 2.604,2.229 0.156,0.198 10 true C

Install the brake actuator assembly to the brake actuator bracket with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Tighten the 3 bolts uniformly in alphabetical order.



Hide 4.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C362113N01
0.333,1.833 0.49,2.031 0.156,0.198 10 false A 2.333,2.729 2.49,2.927 0.156,0.198 10 false B 2.26,1.49 2.448,1.688 0.188,0.198 10 true C

Install the brake actuator with bracket with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 3 nuts uniformly in alphabetical order.

·

Be careful not to damage the brake tubes.

·

Do not drop the actuator. If dropped, replace it.




b.
C362109C01
1.833,1.083 2.5,0.333 2.5,0.333 2.833,0.333 true 1.729,1.188 1.083,0.333 1.083,0.333 0.5,0.333 true 0.5,0.75 1.167,0.75 1.167,0.75 1.625,1.281 true 0.5,1.083 1.167,1.083 1.167,1.083 1.521,1.396 true 2.396,1.375 2.667,1.583 2.667,1.583 3,1.583 true 2.083,1.698 2.417,3.167 2.417,3.167 2.75,3.167 true 2.833,3.083 3.146,3.281 0.313,0.198 10 false *e 2.917,0.25 3.229,0.448 0.313,0.198 10 false *d 0.292,0.979 0.604,1.177 0.313,0.198 10 false *a 0.302,0.667 0.615,0.865 0.313,0.198 10 false *b 0.302,0.229 0.615,0.427 0.313,0.198 10 false *c 3.083,1.5 3.396,1.698 0.313,0.198 10 false *f
*a To Front Wheel Cylinder RH
*b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder RH
*d To Rear Wheel Cylinder LH
*e From 1st Chamber of Brake Master Cylinder Sub-assembly
*f From 2nd Chamber of Brake Master Cylinder Sub-assembly


Set each brake line in the correct position on the brake actuator as shown in the illustration.


c.
C362117C01
2.146,0.219 2.458,0.417 0.313,0.198 10 false *a 1.479,1.823 1.635,2.021 0.156,0.198 10 true A 1.75,1.49 1.906,1.688 0.156,0.198 10 true A 1.875,1.292 2,1.469 0.125,0.177 10 true A 1.948,0.99 2.104,1.188 0.156,0.198 10 false A 1.813,2.125 1.969,2.323 0.156,0.198 10 false B 2.406,1.115 2.563,1.313 0.156,0.198 10 false B
*a Torque Wrench Fulcrum Length


Temporarily install the 6 brake lines to the correct position on the brake actuator assembly as shown in the illustration.


d.

Using a union nut wrench, tighten each brake line.

Specified tightening torque:
for flare nut A:

15.2 N*m (155 kgf*cm, 11 ft.*lbf)

for flare nut B:

19.5 N*m (199 kgf*cm, 14 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

for flare nut A

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf).

·

for flare nut B

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




e.
C362118C01
1.25,1.052 1.24,0.865 false
V113148

Connector Connected
V113147

Lock Lever Locked


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




f.

Attach the clamp to the brake actuator bracket assembly.


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7. YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION