Home › Brake › BRAKE (FRONT) › FRONT BRAKE FLEXIBLE HOSE (w/o VSC) › from 2016.08
RM25T0E _54 Brake _029917 BRAKE (FRONT) _0283239 FRONT BRAKE FLEXIBLE HOSE(w/o VSC) A

BRAKE (FRONT)  FRONT BRAKE FLEXIBLE HOSE(w/o VSC)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47313A 1.INSTALL FRONT FLEXIBLE HOSE (for 1HZ, 1VD-FTV)

a.

Connect the 2 front flexible hoses to the connecting point with each brake line, and then install 4 new clips.


b.
C310926C01
0.281,1.76 0.594,1.917 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect each brake line to the front flexible hose while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting point.




Hide 47313A 2.INSTALL FRONT FLEXIBLE HOSE (for 1GR-FE)

a.

Connect the 2 front flexible hoses to the connecting point with each brake line, and then install 4 new clips.


b.
C310928C01
2.052,0.115 2.365,0.271 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect each brake line to the front flexible hose while holding the rear flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting point.




Hide 47313A 3.INSTALL FRONT FLEXIBLE HOSE LH

a.

Connect the front flexible hose LH to the connecting point with the brake line, and install a new clip.


b.
C310930C01
1.802,0.823 2.115,0.979 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the brake line to the front flexible hose LH while holding the front flexible hose LH with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting point.




c.

Install the front flexible hose LH and a new gasket to the front disc brake cylinder LH with a new union bolt.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely to the lock hole in the front disc brake cylinder LH.



Hide 5.BLEED CLUTCH LINE

Hide 6.INSTALL FRONT WHEEL