Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2016.08–2017.01
RM25T0E _57 Power Source / Network _057931 NETWORKING _0285332 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly CAN main wire or connector

·

Combination meter assembly



WIRING DIAGRAM

C363545E01
5.135,4.104 7.052,4.531 1.917,0.427 10 false Combination Meter Assembly 0.417,1.583 2.333,2.01 1.917,0.427 10 false I112 0.417,1.75 2.333,2.177 1.917,0.427 10 false No. 4 CAN Junction Connector 1.594,1.073 3.51,1.5 1.917,0.427 10 false 2 1.604,0.563 3.521,0.99 1.917,0.427 10 false 1 5.271,0.458 6.042,0.885 0.771,0.427 10 false 13 5.635,0.573 6.406,1 0.771,0.427 10 false CANH 5.656,1.333 6.427,1.76 0.771,0.427 10 false CANL 5.677,1.917 6.448,2.344 0.771,0.427 10 false B 5.667,2.625 6.438,3.052 0.771,0.427 10 false B 5.677,3.323 6.448,3.75 0.771,0.427 10 false ES 5.25,3.333 6.021,3.76 0.771,0.427 10 false L25 5.219,2.646 5.99,3.073 0.771,0.427 10 false L25 5.219,1.958 5.99,2.385 0.771,0.427 10 false L25 5.219,1.208 5.99,1.635 0.771,0.427 10 false L26 5.219,0.677 5.99,1.104 0.771,0.427 10 false L26 5.271,1.021 6.042,1.448 0.771,0.427 10 false 14 5.26,1.75 6.031,2.177 0.771,0.427 10 false 26 5.271,2.417 6.042,2.844 0.771,0.427 10 false 28 5.281,3.115 6.052,3.542 0.771,0.427 10 false 15 1.833,2.625 3.094,3 1.26,0.375 10 false from Ignition Switch 2.271,1.927 3.531,2.302 1.26,0.375 10 false from Battery 3.896,2.156 5.156,2.531 1.26,0.375 10 false DOME NO.1 4.156,2.823 5.417,3.198 1.26,0.375 10 false MET

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
C363466C01
1.385,0.271 1.99,0.552 0.604,0.281 0.427,1.875 0.563,1.875 0.563,1.875 0.781,1.646 true 0.656,2.052 0.792,2.052 0.792,2.052 0.938,1.656 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.521,0.281 1.833,0.438 0.313,0.156 10 false L26 0.031,1.75 0.469,1.938 0.438,0.188 10 false CANH 0.26,1.958 0.698,2.146 0.438,0.188 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C363546C01
1.385,0.219 1.969,0.49 0.583,0.271 0.375,1.854 0.51,1.854 0.51,1.854 0.729,1.49 true 3.083,1.833 2.917,1.833 2.917,1.833 2.698,1.521 true 2.708,2.01 2.542,2.01 2.542,2.01 2.396,1.5 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.552,0.24 1.865,0.438 0.313,0.198 10 false L25 3.135,1.719 3.406,1.927 0.271,0.208 10 false B 2.76,1.906 3.031,2.115 0.271,0.208 10 false B 0.146,1.75 0.417,1.958 0.271,0.208 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L25-26 (B) - Body ground Always 11 to 14 V
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR