Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C306841C03
0.198,0.146 0.51,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND2) Pump motor ground
2 - (Not used)
3 (EXI) 4WD position switch (No. 1 transfer indicator switch) input
4 - (Not used)
5 (EXI4) L4 position switch (No. 1 transfer indicator switch) input
6 - (Not used)
7 - (Not used)
8 - (Not used)
9 - (Not used)
10 (CANL) CAN communication line L
11 (EXI3)* Rear differential lock position switch (No. 4 transfer indicator switch) signal input
12 (IG1) ECU power supply input
13 (BM) Motor relay power supply
14 (SP1) Speed signal output for speedometer
15 (RR-) Rear wheel speed RH (-) signal input
16 (RR+) Rear wheel speed RH (+) power supply output
17 (FL-) Front wheel speed LH (-) signal input
18 (FL+) Front wheel speed LH (+) power supply output
19 - (Not used)
20 - (Not used)
21 - (Not used)
22 (CANH) CAN communication line H
23 (FSW+)* Pull up terminal for rear differential lock position switch (No. 4 transfer indicator switch)
24 (TS) Sensor check input
25 (GND1) Skid control ECU (Brake actuator assembly) ground
26 - (Not used)
27 (HDCS) Pull up terminal for L4 position switch (No. 1 transfer indicator switch)
28 (RL-) Rear wheel speed LH (-) signal input
29 (RL+) Rear wheel speed LH (+) power supply output
30 (FR-) Front wheel speed RH (-) signal input
31 (FR+) Front wheel speed RH (+) power supply output
32 - (Not used)
33 (CSW) VSC OFF switch input
34 - (Not used)
35 (STP) Stop light switch assembly input
36 - (Not used)
37 - (Not used)
38 (+BS) Solenoid relay power supply

*: w/ Rear Differential Lock



TERMINAL INSPECTION


a.

Disconnect the A42 connector and measure the voltage or resistance on the wire harness side.

C306842C27
1.667,1.167 2.104,1.469 0.438,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.771,1.24 2.063,1.427 0.292,0.188 10 false A42
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A42-1 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A42-3 (EXI) - Body ground R-Y - Body ground 4WD position switch (No. 1 transfer indicator switch) input
·

Ignition switch ON

·

Transfer shifted to H2


11 to 14 V
A42-5 (EXI4) - Body ground B-Y - Body ground L4 position switch (No. 1 transfer indicator switch) input
·

Ignition switch ON

·

Transfer shifted to L4


Below 1 Ω
A42-11 (EXI3) - Body ground* R-L - Body ground Rear differential lock position switch (No. 4 transfer indicator switch) signal input
·

Ignition switch ON

·

Rear differential switch ON


Below 1 Ω
A42-12 (IG1) - Body ground B-Y - Body ground ECU power supply input Ignition switch ON 11 to 14 V
A42-13 (BM) - Body ground W - Body ground Motor relay power supply Always 11 to 14 V
A42-14 (SP1) - Body ground G-R - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A42-23 (FSW+) - Body ground* R-Y - Body ground Pull up circuit
·

Ignition switch ON

·

Rear differential switch ON


Below 1 Ω
A42-25 (GND1) - Body ground W-B - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A42-27 (HDCS) - Body ground B-Y - Body ground Pull up circuit
·

Ignition switch ON

·

Transfer shifted to L4


Below 1 Ω
A42-33 (CSW) - Body ground W - Body ground VSC OFF switch input VSC OFF switch pressed and held → released Below 1 Ω → 10 kΩ or higher
A42-35 (STP) - Body ground W - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A42-38 (+BS) - Body ground R - Body ground Solenoid relay power supply Always 11 to 14 V

*: w/ Rear Differential Lock