Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF OFF: Warning light off
ON: Warning light on
-
Brake Warning Light Brake warning light ON or OFF OFF: Warning light off
ON: Warning light on
-
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Parking Brake SW Parking brake switch ON or OFF OFF: Parking brake released
ON: Parking brake applied
-
Inspection Mode Inspection mode Other or Inspect Inspect: Inspection mode
Other: Normal mode
-
Zero Point of M/C Memorized zero value Min.: -12.50 MPa
Max.: 12.40 MPa
- After master cylinder pressure sensor zero point calibration: 2.44 to 2.46 MPa
Deceleration Sensor Acceleration sensor Min.: -18.525 m/s2
Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value Min.: -25.10 m/s2
Max.: 24.90 m/s2
- -
Deceleration Sensor2 Acceleration sensor 2 Min.: -18.525 m/s2
Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value Min.: - 25.10 m/s2
Max.: 24.90 m/s2
- -
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Memorized zero value Min.: - 128°
Max.: 127°
- After completing zero point calibration: 0°
Steering Angle Sensor Steering angle sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle Memorized zero value Min.: -3276.8°
Max.: 3276.7°
- After steering angle sensor zero point calibration: 0°
Lateral G Lateral G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During turning: Changes in proportion with acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value Yaw rate value Min.: -128°/s
Max.: 127°/s
- During turning: Changes in proportion with yaw
Steering Angle Value Steering angle value Min.: -3276.8°
Max.: 3276.7°
- During steering operation: Changes in proportion with steering wheel rotation
Slip Indicator Light Slip indicator light ON or OFF OFF: Indicator light off
ON: Indicator light on
-
Rear Diff Lock Switch Rear differential lock position switch (No. 4 transfer indicator switch) ON or OFF OFF: Rear differential lock position switch off
ON: Rear differential lock position switch on
w/ Rear Differential Lock
Automatic Disconnect Diff SW 4WD position switch (No. 1 transfer indicator switch) ON or OFF OFF: 2WD
ON: 4WD
-
L4 Switch L4 position switch (No. 1 transfer indicator switch) ON or OFF OFF: except L4
ON: L4
-
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.84 m/s2
Max.: 199.27 m/s2
- During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration Min.: -200.84 m/s2
Max.: 199.27 m/s2
- During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.84 m/s2
Max.: 199.27 m/s2
- During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.84 m/s2
Max.: 199.27 m/s2
- During deceleration/acceleration: Changes continuously
FR Wheel ABS Ctrl Status Front wheel RH ABS control status ON or OFF OFF: Not during control
ON: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status ON or OFF OFF: Not during control
ON: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status ON or OFF OFF: Not during control
ON: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status ON or OFF OFF: Not during control
ON: During control
-
BA Ctrl Status BA control status ON or OFF OFF: Not during control
ON: During control
-
TRC(TRAC) Ctrl Status TRC control status ON or OFF OFF: Not during control
ON: During control
-
TRC(TRAC) Engine Ctrl Status TRC engine control status ON or OFF OFF: Not during control
ON: During control
-
TRC(TRAC) Brake Ctrl Status TRC brake control status ON or OFF OFF: Not during control
ON: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status ON or OFF OFF: Not during control
ON: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status ON or OFF OFF: Not during control
ON: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status ON or OFF OFF: Not during control
ON: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status ON or OFF OFF: Not during control
ON: During control
-
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Real Engine Torque Real engine torque Min.: -1024 Nm
Max.: 1023 Nm
- -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0%
Max.: 128%
Accelerator pedal released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
Solenoid Relay Solenoid relay ON or OFF OFF: Solenoid relay off
ON: Solenoid relay on
-
ECB Motor Relay Motor relay ON or OFF OFF: Motor relay off
ON: Motor relay on
ECB: Electronically Controlled Brake
TR(A)C/VSC Solenoid (SM2) Master cut solenoid (SM2) ON or OFF OFF: Not operating
ON: Operating
-
TR(A)C/VSC Solenoid (SM1) Master cut solenoid (SM1) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SFRH) ABS solenoid (SFRH) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SFRR) ABS solenoid (SFRR) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SFLH) ABS solenoid (SFLH) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SFLR) ABS solenoid (SFLR) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SRRH) ABS solenoid (SRRH) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SRRR) ABS solenoid (SRRR) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SRLH) ABS solenoid (SRLH) ON or OFF OFF: Not operating
ON: Operating
-
ABS Solenoid (SRLR) ABS solenoid (SRLR) ON or OFF OFF: Not operating
ON: Operating
-
FR Speed Open Front speed sensor RH open detection Error or Normal Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Error or Normal Normal Error: Momentary interruption
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Error or Normal Normal Error: Momentary interruption
EFI Communication Open ECM communication open detection Error or Normal Normal Error: Momentary interruption
Yaw Rate Open Yaw rate sensor open detection Error or Normal Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection Error or Normal Normal Error: Momentary interruption
Steering Open Steering angle sensor open detection Error or Normal Normal Error: Momentary interruption
Master Cylinder Open Master cylinder pressure sensor open detection Error or Normal Normal Error: Momentary interruption
BS1 Voltage Value +BS voltage value Min.: 0 V
Max.: 20 V
- Changes in proportion to battery voltage
MT Voltage Value Motor voltage value Min.: 0 V
Max.: 20 V
- Changes in proportion to battery voltage
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Number of DTC Number of DTCs recorded Min.: 0
Max.: 255
- -
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Error or Normal Normal Error: Momentary interruption
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Error or Normal Normal Error: Momentary interruption
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Normal Error: Momentary interruption
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Normal Error: Momentary interruption
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Error or Normal Normal Error: Momentary interruption
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Error or Normal Normal Error: Momentary interruption
EFI Communication Invalid ECM communication invalid detection Error or Normal Normal Error: Invalid
Reverse Position Switch Shift lever R position status ON or OFF OFF: Shift lever is not in R
ON: Shift lever is in R
-
Master Cylinder Pressure Master cylinder pressure sensor pressure Min.: 0.00 MPa
Max.: 23.28 MPa
Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C (-112°F)
Max.: 175°C (347°F)
Displays current master cylinder temperature -
Motor Power Supply Voltage Motor power source voltage Min.: 0 V
Max.: 20 V
Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
Solenoid Power Supply Voltage Solenoid power supply voltage Min.: 0 V
Max.: 20 V
Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
Solenoid State for ECU Control Solenoid (for ECU control) ON or OFF OFF: Solenoid relay not operating
ON: Solenoid relay operating
-
Motor State for ECU Control Motor (for ECU control) ON or OFF OFF: Motor relay not operating
ON: Motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion ON or OFF OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Error or Normal Normal Error: Momentary interruption
Solenoid Power Supply Open Solenoid power supply voltage status Error or Normal Normal Error: Momentary interruption
Motor Power Supply Open Motor power supply voltage status Error or Normal Normal Error: Momentary interruption
Stop Switch Open Momentary interruption (open circuit) in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Error or Normal Normal Error: Momentary interruption


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Solenoid Relay Solenoid relay Relay ON/OFF Vehicle condition: Vehicle stopped
Motor Relay Motor relay Relay ON/OFF Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMR) Master cut solenoid (SM2) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMF) Master cut solenoid (SM1) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
Vehicle condition: Vehicle stopped
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
ABS Solenoid Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible Start/Stop Vehicle condition: Vehicle stopped
VSC/TRC(TRAC) Solenoid Selection of multiple VSC/TRC solenoids [SMR (SM2) and SMF (SM1)] possible Start/Stop Vehicle condition: Vehicle stopped