Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.08
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  


SYMPTOM SIMULATION


C206435E03
0.618,0.0 1.6,0.205 0.983,0.205 10 Vibrate Slightly 0.281,2.604 1.264,2.809 0.983,0.205 10 Shake Slightly 1.115,4.114 2.097,4.319 0.983,0.205 10 Vibrate Slightly

HINT:

The most difficult case in troubleshooting is when no problem symptoms occur. In such a case, a thorough problem analysis must be carried out. A simulation of the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be carried out. No matter how much skill or experience a technician has, troubleshooting without confirming the problem symptoms will lead to important repairs being overlooked and mistakes or delays.


a.

Vibration method: When vibration seems to be the major cause.

HINT:

Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


i.

Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.

NOTICE:

Shaking the relays too strongly may result in open relays.



ii.

Slightly shake the connector vertically and horizontally.


iii.

Slightly shake the wire harness vertically and horizontally.

HINT:

The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.





FUNCTION OF SRS WARNING LIGHT


a.

Primary check.

i.

Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If trouble is detected during the primary check, the SRS warning light remains on even after the primary check period (of approximately 6 seconds) has elapsed.




b.

Constant check.

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for trouble.

HINT:

If trouble is detected during the constant check, the airbag sensor assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This blinking pattern indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review.

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


ii.

When the airbag system has trouble:

·

The SRS warning light remains on even after the primary check period has elapsed.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The airbag sensor assembly functions to keep the SRS warning light on if the airbag has been deployed.





CHECK SRS WARNING LIGHT


a.
C093955

Turn the ignition switch to ON and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to the "Problem Symptoms Table".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period has elapsed.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

SRS connectors are located as shown in the illustration..

w/o VSC:
C364257E02
0.177,2.375 1.594,2.635 1.417,0.26 10 false Horn Button Assembly 1.396,1.323 2.865,1.677 1.469,0.354 10 false Spiral Cable Sub-assembly 0.156,3.135 2.354,3.51 2.198,0.375 10 false Instrument Panel Passenger Airbag Assembly* 0.156,3.906 2.354,4.281 2.198,0.375 10 false Front Airbag Sensor LH 4.833,0.188 6.552,0.563 1.719,0.375 10 false Airbag Sensor Assembly 0.135,6.26 3.802,6.604 3.667,0.344 10 false *: w/ Instrument Panel Passenger Airbag Assembly 0.146,4.667 2.344,5.042 2.198,0.375 10 false Front Airbag Sensor RH 0.156,5.448 2.354,5.823 2.198,0.375 10 false Combination Meter Assembly 5.656,1.115 5.875,1.354 0.219,0.24 10 false A 4.677,0.938 4.896,1.177 0.219,0.24 10 false 1 5.667,0.927 5.885,1.167 0.219,0.24 10 false 2 2.813,4.552 3.031,4.792 0.219,0.24 10 false 19 3.885,1.323 4.104,1.563 0.219,0.24 10 false 5 3.594,1.313 3.813,1.552 0.219,0.24 10 false 6 3.167,1.24 3.385,1.479 0.219,0.24 10 false 7 3,1.135 3.219,1.375 0.219,0.24 10 false 8 2.792,2.26 3.01,2.5 0.219,0.24 10 false 9 2.594,2.208 2.813,2.448 0.219,0.24 10 false 10 2.792,3.063 3.01,3.302 0.219,0.24 10 false 13 2.625,2.979 2.844,3.219 0.219,0.24 10 false 14 3.865,3.875 4.083,4.115 0.219,0.24 10 false 15 3.531,3.875 3.75,4.115 0.219,0.24 10 false 16 2.813,3.813 3.031,4.052 0.219,0.24 10 false 17 2.625,3.75 2.844,3.99 0.219,0.24 10 false 18 3.531,3.125 3.75,3.365 0.219,0.24 10 false 12 3.854,3.125 4.073,3.365 0.219,0.24 10 false 11 6.615,0.927 6.833,1.167 0.219,0.24 10 false 2 4.677,1.292 4.896,1.531 0.219,0.24 10 false 3 5.667,1.292 5.885,1.531 0.219,0.24 10 false 4 6.615,1.292 6.833,1.531 0.219,0.24 10 false 4 2.646,4.5 2.865,4.74 0.219,0.24 10 false 20 2.802,5.313 3.021,5.552 0.219,0.24 10 false 21 2.615,5.25 2.833,5.49 0.219,0.24 10 false 22

w/ VSC:
C364685E01
1.344,1.479 2.896,1.844 1.552,0.365 10 false Spiral Cable Sub-assembly 4.927,0.24 6.531,0.615 1.604,0.375 10 false Airbag Sensor Assembly 0.26,2.51 1.792,2.885 1.531,0.375 10 false Horn Button Assembly 0.26,3.292 2.188,3.667 1.927,0.375 10 false Instrument Panel Passenger Airbag Assembly 0.26,4.125 2.042,4.427 1.781,0.302 10 false Front Airbag Sensor LH 0.24,4.896 2.021,5.198 1.781,0.302 10 false Front Airbag Sensor RH 0.229,5.698 2.406,6 2.177,0.302 10 false Combination Meter Assembly 0.188,6.469 2.396,6.865 2.208,0.396 10 false Lower No. 1 Instrument Panel Airbag Assembly* 4.698,1.031 4.854,1.229 0.156,0.198 10 false 1 5.667,1.208 5.875,1.448 0.208,0.24 10 false A 4.698,1.385 4.854,1.583 0.156,0.198 10 false 3 6.625,1.385 6.781,1.583 0.156,0.198 10 false 4 3.938,1.479 4.094,1.677 0.156,0.198 10 false 5 3.583,1.458 3.74,1.656 0.156,0.198 10 false 6 3.229,1.333 3.385,1.531 0.156,0.198 10 false 7 3.031,1.271 3.188,1.469 0.156,0.198 10 false 8 2.844,2.406 3,2.604 0.156,0.198 10 false 9 2.646,2.344 2.896,2.635 0.25,0.292 10 false 10 3.885,3.24 4.073,3.427 0.188,0.188 10 false 11 3.563,3.24 3.75,3.427 0.188,0.188 10 false 12 2.844,3.219 3.083,3.51 0.24,0.292 10 false 13 2.646,3.146 2.896,3.427 0.25,0.281 10 false 14 3.885,4.063 4.177,4.292 0.292,0.229 10 false 15 3.531,4.063 3.792,4.385 0.26,0.323 10 false 16 2.625,3.938 2.896,4.271 0.271,0.333 10 false 18 2.792,4.021 3.229,4.396 0.438,0.375 10 false 17 2.813,4.781 3.219,5.156 0.406,0.375 10 false 19 2.635,4.719 3.01,5.146 0.375,0.427 10 false 20 0.365,7.406 3.208,7.635 2.844,0.229 10 false *: w/ Pretensioner 5.677,1.021 5.833,1.219 0.156,0.198 10 false 2 6.615,1.021 6.771,1.219 0.156,0.198 10 false 2 5.677,1.385 5.833,1.583 0.156,0.198 10 false 4 2.635,5.51 3.042,5.885 0.406,0.375 10 false 22 2.813,6.375 3.219,6.75 0.406,0.375 10 false 23 2.813,5.583 3.219,5.958 0.406,0.375 10 false 21 2.635,6.323 3.042,6.698 0.406,0.375 10 false 24

C364686E01
1.594,1.75 1.75,1.948 0.156,0.198 10 false A 4.042,2.063 4.333,2.323 0.292,0.26 10 false 25 4.458,2.177 7.156,2.479 2.698,0.302 10 false Front Seat Outer Belt Assembly LH 4.458,3.052 6.74,3.375 2.281,0.323 10 false Curtain Shield Airbag Assembly LH 4.458,3.875 6.781,4.219 2.323,0.344 10 false Door Side Airbag Sensor LH 4.448,4.729 7.156,5.052 2.708,0.323 10 false Front Seat Outer Belt Assembly RH 4.448,5.563 7.156,5.885 2.708,0.323 10 false Curtain Shield Airbag Assembly RH 4.448,6.396 7.156,6.719 2.708,0.323 10 false Door Side Airbag Sensor RH 4.219,1.979 4.604,2.354 0.385,0.375 10 false 26 4.042,2.917 4.375,3.313 0.333,0.396 10 false 27 4.219,2.823 4.49,3.156 0.271,0.333 10 false 28 4.031,4.604 4.542,5.146 0.51,0.542 10 false 25 4.219,4.521 4.5,4.875 0.281,0.354 10 false 26 4.031,5.458 4.521,5.802 0.49,0.344 10 false 27 4.208,5.385 4.688,5.781 0.479,0.396 10 false 28 0.677,0.76 3.375,1.063 2.698,0.302 10 false Airbag Sensor Assembly 0.26,0.083 2.958,0.385 2.698,0.302 12 false w/ Pretensioner: 0.604,1.563 0.917,1.854 0.313,0.292 10 false 1 1.604,1.552 1.917,1.844 0.313,0.292 10 false 2 2.542,1.563 2.854,1.854 0.313,0.292 10 false 2 2.542,1.927 2.854,2.219 0.313,0.292 10 false 4 1.604,1.927 1.917,2.219 0.313,0.292 10 false 4 0.604,1.938 0.917,2.229 0.313,0.292 10 false 3 4.208,3.688 4.583,4.01 0.375,0.323 10 false 30 4.042,3.75 4.417,4.073 0.375,0.323 10 false 29 4.031,6.281 4.406,6.604 0.375,0.323 10 false 29 4.208,6.198 4.583,6.521 0.375,0.323 10 false 30

Connector Type Application
Terminal Twin-Lock Mechanism Connectors 5, 7, 11, 16
Half Connection Prevention Mechanism Connectors 5, 7, 11, 16
Activation Prevention Mechanism Connectors 3, 4, 6, 8, 10, 12, 14, 24, 26, 28
Connector Lock Mechanism (1) Connectors 9, 13, 23, 25, 27
Connector Position Assurance Mechanism Connectors 5, 16, 17, 19, 29
Connector Lock Mechanism (2) Connectors A
Improper Connection Prevention Lock Mechanism Connectors A


b.

Terminal twin-lock mechanism

C190972E06
2.438,0.094 2.052,0.094 false 2.823,0.646 2.438,0.094 false 5.708,0.094 5.573,0.094 false 5.823,0.635 5.708,0.094 false 0.646,0.021 2,0.198 1.354,0.177 10 Lance (Primary Lock) 1.229,1.448 2.167,1.625 0.938,0.177 10 Primary Lock 3.948,0.021 5.625,0.198 1.677,0.177 10 Spacer (Secondary Lock) 4.896,1.427 5.948,1.604 1.052,0.177 10 Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E18
1.427,1.083 1.271,1.073 false 1.552,1.417 1.427,1.083 false 1.719,0.813 1.5,0.813 false 1.833,1.365 1.719,0.813 false 2.146,0.531 1.938,0.531 false 2.354,1.344 2.146,0.531 false 3.219,0.563 3.406,0.563 false 2.99,1.198 3.219,0.563 false 3.458,0.865 3.635,0.875 false 3.25,1.323 3.458,0.865 false 5.917,0.74 5.729,0.74 false 6.073,1.146 5.917,0.74 false 1.125,0.458 1.958,0.625 0.833,0.167 10 Locking Arm 0.979,0.729 1.521,0.896 0.542,0.167 10 Stopper 0.469,1 1.302,1.177 0.833,0.177 10 Locking Part 3.448,0.5 3.885,0.688 0.438,0.188 10 Slider 3.667,0.802 4.135,0.99 0.469,0.188 10 Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 Stopper 4.708,1.906 6.042,2.094 1.333,0.188 10 Rebound by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected by the force of the spring so that no continuity exists.



d.

Activation prevention mechanism

C279106E09
2.667,1.292 3.167,0.865 false 2.854,1.354 3.177,0.865 false 3,1.573 3.26,1.25 false 1.417,0.844 1.906,0.969 false 1.271,1.365 1.854,1.365 false 1.458,1.76 2.052,1.573 false 4.25,1.51 5.125,1.375 false 1.042,3.771 0.552,3.052 false 1.042,3.771 0.771,3.052 false 1.042,3.771 1.021,3.063 false 1.042,3.76 1.26,3.052 false 1.052,3.75 1.51,3.052 false 1.042,3.76 0.542,3.313 false 1.052,3.76 1.5,3.302 false 3.615,3.031 3.76,3.563 3.76,3.563 3.885,3.021 false 2.479,3.25 2.615,3.563 2.615,3.563 2.74,3.24 false 3.885,3.25 3.76,3.542 3.76,3.542 3.615,3.25 false 6.146,3.792 6.073,3.313 true 6.146,3.802 6.208,3.302 true 2.75,3.031 2.615,3.594 2.615,3.594 2.479,3.031 false 2.042,0.188 2.865,0.385 0.823,0.198 10 false When open 3.219,0.781 4.375,0.979 1.156,0.198 10 false Female Terminal 0.385,1.271 1.313,1.49 0.927,0.219 10 false Male Terminal 0.292,1.688 1.5,1.927 1.208,0.24 10 false Short Spring Plate 3.198,1.531 4.417,2.042 1.219,0.51 10 false Short spring plate contacting the male terminal 3.313,1.135 4.438,1.333 1.125,0.198 10 false Female Housing 5.333,0.229 6.323,0.427 0.99,0.198 10 false When shorted 4.635,1.781 7.115,2.146 2.479,0.365 10 false Front view of wire harness connector: (to Spiral with Sensor Cable Sub-assembly) 2.198,3.615 3.198,4.031 1,0.417 10 false Short Spring (to Floor Wire) 0.188,3.833 1.99,4.198 1.802,0.365 10 false Short Spring (to Cowl Wire) 0.531,0.729 1.458,0.938 0.927,0.208 10 false Male Housing 3.271,3.615 4.365,3.969 1.094,0.354 10 false Short Spring (to Floor Wire) 5.729,3.823 6.563,4.042 0.833,0.219 10 false Short Spring 1.146,2.146 3.417,2.521 2.271,0.375 10 false Front view of wire harness connector: (to Airbag Sensor Assembly)

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E12
2.521,0.354 2.021,0.198 false 2.635,0.802 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.99,0.938 1.708,0.333 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector locking button engages the locking button claw in the groove of the other connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E01
1.058,0.13 2.269,0.299 1.211,0.170 10 Female Connector 1.261,0.41 2.097,0.580 0.836,0.170 10 Locking Part 1.003,2.219 2.062,2.396 1.059,0.177 10 Male Connector 2.963,0.298 4.550,0.454 1.586,0.156 10 Primary Lock Completed 5.072,0.298 6.839,0.454 1.767,0.156 10 Secondary Lock Completed 4.898,0.699 5.526,0.875 0.628,0.177 10 Retainer 0.858,0.198 1.016,0.2 false 0.837,1.105 0.858,0.198 false 1.051,0.478 1.217,0.478 false 0.933,1.2 1.051,0.478 false 0.727,2.289 0.958,2.289 false 0.511,1.797 0.727,2.289 false 5.63,0.779 5.464,0.779 false 5.66,1.096 5.63,0.779 false

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side. The secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, the connectors are completely engaged.



g.

Connector lock mechanism (2)

C279127E04
0.552,2.01 1.135,2 1.135,2 1.135,1.573 false 1.823,3.375 1.844,3.563 1.844,3.563 2.583,3.563 false 3.813,3.26 4.188,3.26 4.188,3.26 4.188,2.906 false 4.365,1.604 4.688,1.604 false 5.521,2.719 5.74,2.719 false 5.865,2.833 6.031,2.833 false 4.833,3.417 5.5,3.417 false 0.146,1.917 0.625,2.135 0.479,0.219 10 Lance 2.646,3.479 3.271,3.656 0.625,0.177 10 Retainer 4.719,1.521 5.344,1.719 0.625,0.198 10 Holder 3.26,3.146 3.813,3.344 0.552,0.198 10 Retainer 4.281,3.313 4.844,3.521 0.563,0.208 10 Retainer 5.073,2.615 5.542,2.813 0.469,0.198 10 Holder 6.052,2.75 6.396,2.927 0.344,0.177 10 Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer with the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C279130E03
4.167,3.375 4.625,3.375 false 0.958,2.719 1.188,2.719 1.188,2.719 1.188,1.531 false 4.167,1.49 4.719,1.49 4.719,1.49 5.031,0.969 false 5.031,0.552 5.031,0.188 5.031,0.188 5.625,0.188 false 1.167,1.083 1.167,0.792 1.167,0.792 1.333,0.792 false 0.271,2.635 1.021,2.844 0.75,0.208 10 Unlock Rib 3.365,0.052 4.01,0.26 0.646,0.208 10 Top View 5.677,0.104 6.427,0.313 0.75,0.208 10 Unlock Rib 3.479,1.365 4.156,1.75 0.677,0.385 10 Temporary Hold Lock 3.771,3.26 4.229,3.479 0.458,0.219 10 Lever 1.385,0.708 1.563,0.896 0.177,0.188 10 A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the A axis.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag sensor assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm [0.0197 in.]) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C364410E01
1.344,0.333 1.708,0.531 0.365,0.198 0.865,4.083 1.292,4.302 0.427,0.219 0.99,5.771 1.417,5.99 0.427,0.219 3.604,0.313 3.979,0.521 0.375,0.208 5.615,0.302 5.99,0.51 0.375,0.208 0.979,7.292 1.354,7.49 0.375,0.198 0.917,0.99 1.479,1.844 1.479,1.844 1.802,0.979 true 5.542,1.354 5.781,1.854 5.781,1.854 5.552,0.927 true 4.021,0.958 3.792,1.854 3.792,1.854 4.021,1.333 true 2.969,2.823 3.313,2.74 3.313,2.74 3.104,3.229 true 5.938,2.823 6.156,2.604 6.156,2.604 5.948,3.25 true 2.396,3.375 2.927,3.573 2.927,3.573 2.344,2.969 true 5.396,3.385 5.927,3.583 5.927,3.583 5.344,2.979 true 1.969,5.125 2.031,5.625 2.031,5.625 2.104,5.125 true 4.344,5 4.51,5.5 true 6.542,4.625 6.385,4.99 true 3.938,6.583 4.083,6.25 true 6.448,6.573 6.594,6.24 true 3.396,6.677 3.542,6.865 true 5.969,6.708 5.854,6.885 true 1.177,6.729 1.26,6.927 1.26,6.927 1.333,6.719 true 3.51,4.813 4.115,4.469 true 5.115,4.469 5.49,4.813 true 1.51,0.958 1.469,1.833 true 1.083,7.979 1.167,8.302 1.167,8.302 1.24,7.969 true 3.323,8.135 3.406,8.323 true 6.396,7.99 6.542,7.656 true 5.906,8.115 5.792,8.292 true 3.875,7.99 4.021,7.656 true 0.115,0.021 5.01,0.219 4.896,0.198 10 false Airbag Sensor Assembly Connector 1.135,1.865 2.354,2.083 1.219,0.219 10 false Short Spring 3.427,1.896 4.646,2.115 1.219,0.219 10 false Short Spring 5.531,1.927 6.75,2.146 1.219,0.219 10 false Short Spring 3.365,2.51 4.583,2.729 1.219,0.219 10 false Paper 1.5,2.198 2.719,2.417 1.219,0.219 10 false Before Release 6.229,2.417 7.083,2.646 0.854,0.229 10 false Paper 3,3.531 4.219,3.75 1.219,0.219 10 false Short Spring 5.99,3.5 6.833,3.781 0.844,0.281 10 false Short Spring 0.063,4.073 0.844,4.26 0.781,0.188 10 false Connector 3.135,4.156 4.25,4.344 1.115,0.188 10 false Before Release 5.365,4.188 6.479,4.375 1.115,0.188 10 false After Release 4.25,4.323 5.365,4.51 1.115,0.188 10 false Short Spring 4.5,5.51 4.948,5.74 0.448,0.229 10 false Paper 6.615,4.542 7.063,4.771 0.448,0.229 10 false Paper 2.813,5.823 3.927,6.01 1.115,0.188 10 false Before Release 5.302,5.833 6.417,6.021 1.115,0.188 10 false After Release 4.167,6.094 4.615,6.323 0.448,0.229 10 false Paper 3.542,6.927 4.656,7.115 1.115,0.188 10 false Short Spring 5.188,6.917 6.063,7.115 0.875,0.198 10 false Short Spring 0.917,6.958 2.031,7.146 1.115,0.188 10 false Short Spring 0.125,5.781 0.906,5.969 0.781,0.188 10 false Connector 1.49,0.354 1.906,0.563 0.417,0.208 10 false 3 3.76,0.333 4.177,0.542 0.417,0.208 10 false 4 5.771,0.323 6.188,0.531 0.417,0.208 10 false 4 1,4.115 1.417,4.323 0.417,0.208 10 false 8 1.115,5.802 1.531,6.01 0.417,0.208 10 false 12 1.677,5.708 2.792,5.896 1.115,0.188 10 false Short Spring 6.615,6.063 7.063,6.292 0.448,0.229 10 false Paper 4.469,2.208 5.583,2.396 1.115,0.188 10 false After Release 2.521,7.219 3.635,7.406 1.115,0.188 10 false Before Release 5.167,7.24 6.281,7.427 1.115,0.188 10 false After Release 0.771,8.344 1.885,8.531 1.115,0.188 10 false Short Spring 3.26,8.365 4.375,8.552 1.115,0.188 10 false Short Spring 6.615,7.51 7.063,7.74 0.448,0.229 10 false Paper 5.229,8.354 6.104,8.552 0.875,0.198 10 false Short Spring 0.094,7.333 0.875,7.521 0.781,0.188 10 false Connector 1.125,7.313 1.542,7.521 0.417,0.208 10 false 6 4.073,7.51 4.521,7.74 0.448,0.229 10 false Paper