Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.08
RM25T0E _51 Engine / Hybrid System _057930 CRUISE CONTROL _0287962 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Vehicle Spd Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual vehicle speed -
CCS Mem Vehicle Spd Stored vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (159 mph)
Actual stored vehicle speed -
Throttle Opening Angle Required throttle opening amount Min.: 0%
Max.: 100%
Required throttle opening angle -
Cruise Control Cruise control system active condition OFF or ON ON: Cruise control activated
OFF: Cruise control deactivated
-
Cruise Main Switch Operation Condition Cruise control main switch status OFF or ON ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Main SW M-CPU Cruise control main switch signal (Main CPU) OFF or ON ON: Cruise control main switch on
OFF: Cruise control main switch off
-
CCS Ready M-CPU Cruise control system standby condition (Main-CPU) OFF or ON ON: Cruise control main switch (Main CPU) SET
OFF: Cruise control main switch (Main CPU) UNSET
-
CCS Indicator M-CPU Cruise control indicator light signal (Main-CPU) OFF or ON ON: Cruise control indicator light turns on
OFF: Cruise control indicator light turns off
-
Cancel Switch CANCEL switch signal OFF or ON ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal OFF or ON ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal OFF or ON ON: +RES switch on
OFF: +RES switch off
-
Stop Light Switch 1 Stop light switch signal OFF or ON ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch 2 Stop light switch signal OFF or ON ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status Shift lever position signal OFF or ON ON: Cruise control operated
OFF: Cruise control operation stopped
-
Brake Cancel Switch Brake cancel signal OFF or ON ON: Brake pedal depressed
OFF: Brake pedal released
-
HINT:
·

If any DTCs are output, the value for a measurement item may be incorrect.


·

If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.





PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

HINT:

The ignition switch must be turned on to proceed with the Active Test using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light OFF or ON -
Indicat. SET SET indicator light OFF or ON -