Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2017.01
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be a ECM malfunction.



WIRING DIAGRAM

C261918E31
1.458,2.646 3.427,2.906 1.969,0.26 10 false ECM 1.292,3.438 1.573,3.635 0.281,0.198 10 false CG 1.792,3.438 2.073,3.635 0.281,0.198 10 false TC 2.063,3.333 2.281,3.521 0.219,0.188 10 false 13 1.26,2.438 2.635,2.781 1.375,0.344 10 false A29*1, I84*2 2.083,1.573 2.323,1.781 0.24,0.208 10 false 27 1.802,1.677 2.083,1.865 0.281,0.188 10 false TC 1.229,3.917 1.583,4.115 0.354,0.198 10 false I17 5.948,3.833 6.281,4.031 0.333,0.198 10 false I51 1.229,4.083 1.719,4.281 0.49,0.198 10 false DLC3 0.531,4.438 3.063,4.656 2.531,0.219 10 false : CAN Communication Line 5.917,3.979 6.823,4.354 0.906,0.375 10 false Airbag Sensor Assembly 1.104,3.313 1.25,3.552 0.146,0.24 10 false 4 2.552,4.156 7.156,4.51 4.604,0.354 10 false *1: for RHD 2.552,4.458 7.156,4.813 4.604,0.354 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM

Result:
Proceed to
DTCs are output
DTC is not output




DTCs are output

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.
C364749C01
1.021,0.146 1.458,0.427 0.438,0.281 1.927,0.135 2.365,0.417 0.438,0.281 1.531,2.656 1.969,2.938 0.438,0.281 2.302,1.146 2.979,1.531 2.979,1.531 3.104,1.531 true 1.802,3.875 2.094,4.323 2.094,4.323 2.26,4.323 true 1.115,0.198 1.573,0.396 0.458,0.198 10 false A29 2.052,0.198 2.51,0.396 0.458,0.198 10 false I84 1.521,0.177 1.979,0.375 0.458,0.198 10 false *A 2.427,0.177 2.885,0.375 0.458,0.198 10 false *B 0.177,0.188 0.635,0.385 0.458,0.198 10 false *a 0.219,2.833 0.677,3.031 0.458,0.198 10 false *b 1.677,2.698 2.135,2.896 0.458,0.198 10 false I17 3.177,1.458 3.427,1.729 0.25,0.271 10 false TC 2.323,4.24 2.573,4.51 0.25,0.271 10 false TC
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
I17-13 (TC) - A29-27 (TC) Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
I17-13 (TC) - I84-27 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C34
1.458,0.281 1.844,0.51 0.385,0.229 1.635,0.917 2.292,0.479 true 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 2.344,0.406 2.625,0.594 0.281,0.188 10 false CG 1.563,0.313 1.854,0.458 0.292,0.146 10 false I17
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C364750C01
0.063,0.708 0.427,0.958 0.365,0.25 0.063,1.104 0.427,1.354 0.365,0.25 2.25,0.958 2.885,1.313 2.885,1.313 3.052,1.313 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.469,0.74 0.781,0.938 0.313,0.198 10 false *A 0.469,1.167 0.781,1.365 0.313,0.198 10 false *B 0.135,0.75 0.448,0.948 0.313,0.198 10 false A29 0.156,1.156 0.469,1.354 0.313,0.198 10 false I84 3.104,1.219 3.344,1.417 0.24,0.198 10 false TC
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A29-27 (TC) - Body ground Always 10 MΩ or higher

for LHD
Tester Connection Condition Specified Condition
I84-27 (TC) - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU