Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD › from 2016.08
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132957 CYLINDER HEAD A

1VD-FTV ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CYLINDER HEAD STUD BOLT

HINT:

If a cylinder head stud bolt is deformed or the threads are damaged, replace it.


a.
A164548

Using an E8 "TORX" socket wrench, install the cylinder head stud bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 11117E 2.INSTALL NO. 1 STRAIGHT SCREW PLUG WITH HEAD

a.

Using a 6 mm hexagon wrench, install a new gasket and the No. 1 straight screw plug with head.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG WITH HEAD (w/ DPF)

a.

Install a new gasket with the No. 1 straight screw plug with head.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 23699A 4.INSTALL NOZZLE HOLDER CLAMP SEAT (w/o DPF)

a.

Install the 4 nozzle holder clamp seats.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head sub-assembly.


Hide 13711A 6.INSTALL VALVE STEM OIL SEAL

a.
A164546C01
0.583,1.167 1.333,1.167 true 2.833,1.031 2.917,1.198 2.917,1.198 2.917,1.365 true 3,2.167 3,1.615 true 2.917,2.177 3.229,2.333 0.313,0.156 10 false *1 0.708,2.271 1.021,2.427 0.313,0.156 10 false *a 2.208,2.281 2.521,2.438 0.313,0.156 10 false *b 2.792,1.365 3.25,1.563 0.458,0.198 10 false SST 3.083,0.75 3.24,0.948 0.156,0.198 10 true A 0.292,1.073 0.583,1.333 0.292,0.26 10 true SST
*1 Cylinder Head Sub-assembly
*a CORRECT
*b INCORRECT


Apply a light coat of engine oil to a new valve stem oil seal and valve guide.


b.

Using SST, push in the valve stem oil seal.

SST
09201-41020  

Standard protrusion height labeled A:

Below 14.7 mm (0.579 in.)



Hide 13711 7.INSTALL VALVE

a.
A075640C02
2.146,0.583 2.458,0.74 0.313,0.156 10 false *a
*a 50 mm (1.97 in.)


Apply plenty of engine oil to the tip area of the valve shown in the illustration.


b.

Place the cylinder head sub-assembly on a wooden block.


c.

Install the valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



d.
A164542N02
0.583,2 0.75,2 0.75,2 1.167,1.583 true 3.083,0.417 3.083,0.25 3.083,0.25 2.833,0.25 true 2.948,0.427 3.271,0.625 0.323,0.198 10 false SST 0.292,1.917 0.615,2.115 0.323,0.198 10 false SST

Using SST, compress the inner compression spring and place the valve spring retainer lock around the valve stem.

SST
09202-70020  (09202-00010)


e.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve stem tip.