1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE
| *a | 35 mm (1.38 in.) |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| Runout | Specified Condition |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
If the runout is more than the maximum, replace the companion flange.
2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR
Using a dial indicator, measure the ring gear runout.
0.05 mm (0.00197 in.)
If the runout is more than the maximum, replace the ring gear.
3.INSPECT DIFFERENTIAL RING GEAR BACKLASH
Using a dial indicator, measure the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not as specified, adjust the side bearing preload or repair as necessary.
Measure at 3 or more positions around the circumference of the ring gear.
4.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
0.89 to 1.41 N*m (10 to 14 kgf*cm, 8 to 12 in.*lbf)
If necessary, disassemble and inspect the differential.
41204G 5.REMOVE REAR DRIVE PINION COMPANION FLANGE NUT
41204 6.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
41201C 7.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
41214 8.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
41201B 9.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
Using SST, remove the rear drive pinion front tapered roller bearing (inner race) from the differential drive pinion.
If the rear drive pinion front tapered roller bearing is damaged or worn, replace the rear drive pinion front tapered roller bearing.
41316 10.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK
Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.
11.REMOVE DIFFERENTIAL CASE ASSEMBLY
| *a | Matchmark |
Place matchmarks on the bearing caps and differential carrier.
Remove the 4 bolts, 2 bearing caps and 2 rear differential bearing adjusting nuts.
Remove the differential case and 2 rear differential case bearings (outer race) from the differential carrier.
Tag the 2 rear differential case bearings (outer race) to show the location for reassembly.
12.REMOVE DIFFERENTIAL DRIVE PINION
Remove the differential drive pinion from the differential carrier.
41231 13.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the rear differential drive pinion bearing spacer from the differential carrier.
41201A 14.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner race).
If either the drive pinion or ring gear is damaged, replace them as a set.
41201D 15.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER
Remove the rear differential drive pinion plate washer from the differential drive pinion.
41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
Using a brass bar and hammer, tap out the rear drive pinion front tapered roller bearing (outer race).
41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer race).
18.REMOVE DIFFERENTIAL RING GEAR
| *a | Matchmark |
Place matchmarks on the differential ring gear and differential case.
Remove the 12 differential ring gear set bolts.
Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case.
19.INSPECT RUNOUT OF DIFFERENTIAL CASE
If the differential ring gear runout is at the maximum or less, this inspection is not necessary.
Install the 2 rear differential case bearings (outer race) to the differential case.
Install the differential case to the differential carrier.
Install the 2 rear differential bearing adjusting nuts.
Install the 2 bearing caps to the differential carrier with the 4 bolts.
Using a dial indicator, measure the differential case runout.
0.04 mm (0.00157 in.)
Remove the 4 bolts and 2 bearing caps.
Remove the 2 rear differential bearing adjusting nuts.
Remove the differential case.
Remove the 2 rear differential case bearings (outer race).
41301A 20.REMOVE REAR DIFFERENTIAL CASE BEARING
Using SST, remove the 2 rear differential case bearings from the differential case.
21.DISASSEMBLE DIFFERENTIAL CASE
| *a | Matchmark |
Place matchmarks on the differential case LH and RH.
Remove the 8 bolts uniformly, a little at a time.
Using a plastic-faced hammer, separate the differential case LH and RH.
Remove the 2 rear No. 1 differential side gear thrust washers, 2 rear differential side gears, rear differential spider, 4 rear differential pinions and 4 rear differential pinion thrust washers.