Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) › from 2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136709 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  DISASSEMBLY  


PROCEDURE

Hide 41204 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE REAR SUB-ASSEMBLY

a.
C236648C09
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 35 mm (1.38 in.)


Using a dial indicator, measure the vertical and lateral runout of the companion flange.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161871

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161872

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


Hide 4.INSPECT DRIVE PINION PRELOAD

a.
C124126

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard drive pinion preload (at starting):

0.89 to 1.41 N*m (10 to 14 kgf*cm, 8 to 12 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 5.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

Standard total preload (at starting):

0.29 to 0.49 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf) + Standard drive pinion preload


If necessary, disassemble and inspect the differential.


Hide 84222D 6.REMOVE NO. 4 TRANSFER INDICATOR SWITCH

a.
C311225

Remove the No. 4 transfer indicator switch.


Hide 41456 7.REMOVE REAR DIFFERENTIAL LOCK COVER

a.
C311223

Remove the 3 bolts.


b.

Using a brass bar and hammer, tap on the rear differential lock cover to remove it.


Hide 41450 8.REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

a.
C161873

Remove the 4 bolts.


b.
C308014

Remove the shift fork shaft bolt.


c.

Using a screwdriver, pull out the differential lock shift actuator and remove the rear differential lock sleeve and rear differential lock shift fork.


Hide 41204G 9.REMOVE REAR DRIVE PINION COMPANION FLANGE NUT

Hide 41204 10.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41201C 11.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41214 12.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 13.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C124133N08
1.662,0.743 0.99,0.509 false 0.603,0.43 0.897,0.573 0.294,0.143 10 SST

Using SST, remove the rear drive pinion front tapered roller bearing (inner race) from the differential drive pinion.

SST
09556-22010  

If the rear drive pinion front tapered roller bearing is damaged or worn, replace the rear drive pinion front tapered roller bearing.


Hide 41302 14.REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C161875C01
1.219,1.354 0.438,1.74 0.438,1.74 1.229,1.427 true 0.26,1.656 0.573,1.854 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the bearing caps and differential carrier.


b.

Remove the 4 bolts and 2 bearing caps.


c.
C161876N01
1.794,0.716 2.509,0.492 false 2.56,0.372 2.851,0.526 0.292,0.155 10 SST

Using SST and a hammer, remove the 2 plate washers.

SST
09504-22012  

HINT:

Measure the thickness of each plate washer and note it down.



d.
C164228N01
1.166,1.346 1.409,1.513 0.243,0.167 10 LH 2.567,1.338 2.81,1.504 0.243,0.167 10 RH

Remove the differential case with the 2 rear differential case bearings (outer race) from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer race) to show the location for reassembly.



Hide 15.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the differential drive pinion from the differential carrier.


Hide 41231 16.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Remove the rear differential drive pinion bearing spacer from the differential carrier.


Hide 41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237656N06
2.731,0.394 3.04,0.551 0.309,0.157 10 SST 2.334,1.03 2.605,0.467 2.605,0.467 2.697,0.467 false

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner race).

SST
09950-00020  

If either the drive pinion or ring gear is damaged, replace them as a set.


Hide 41201D 18.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

a.

Remove the rear differential drive pinion plate washer from the differential drive pinion.


Hide 41201B 19.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161839

Using a brass bar and hammer, tap out the rear drive pinion front tapered roller bearing (outer race).


Hide 41201A 20.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162552

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer race).


Hide 21.REMOVE DIFFERENTIAL RING GEAR

a.
C161840C01
1.24,1.313 2.167,1.208 2.167,1.208 1.219,1.458 true 2.208,1.125 2.969,1.292 0.76,0.167 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 12 differential ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case.


Hide 22.INSPECT RUNOUT OF DIFFERENTIAL CASE

a.

Place the 2 rear differential case bearings (outer race) on their respective bearings.

HINT:

Do not interchange the left and right outer races.



b.

Install the assembled plate washers onto the rear differential case bearing.


c.

Install the differential case onto the differential carrier.

HINT:

If it is difficult to install the differential case onto the carrier, replace the plate washer with a thinner one.


However, select a plate washer that allows no clearance between it and the carrier.


d.

Align the matchmarks on the bearing caps and differential carrier.


e.

Install and uniformly tighten the 4 bolts a little at a time.


f.
C161878

Using a dial indicator, measure the differential case runout.

Maximum case runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the differential case and side bearing as a set.


g.

Remove the differential case.


Hide 23.DISASSEMBLE DIFFERENTIAL CASE

a.
C161879C01
1.625,1.26 2.302,1.167 2.302,1.167 1.604,1.135 true 2.375,1.063 3.198,1.229 0.823,0.167 10 false *a
*a Matchmark


Place matchmarks on the differential case and differential cover.


b.

Using a T10 "TORX" socket, remove the 5 set bolts and 3 pinion shaft pins.


c.

Separate the differential cover and differential case.


d.

Remove the 2 rear differential side gears, 2 rear No. 1 differential side gear thrust washers, 4 rear differential pinions, 4 rear differential pinion thrust washers, 2 rear No. 1 differential pinion shafts, rear differential pinion shaft and rear differential pinion shaft holder from the differential case.


Hide 41301A 24.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C161880N01
1.583,1.021 2.208,0.729 2.208,0.729 1.76,0.604 true 2.271,0.656 2.625,0.813 0.354,0.156 10 false SST

Using SST, remove the rear differential case bearing.

SST
09950-40011  (09952-04010, 09953-04020, 09954-04010, 09955-04061)
09950-60010  (09951-00580)

HINT:

Fix the claws of SST to the notches in the differential case.



Hide 41301A 25.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C161881N01
0.948,1.073 0.635,0.698 0.635,0.698 1,0.896 false 0.26,0.563 0.594,0.719 0.333,0.156 10 false SST

Using SST, 4 bolts and a press, remove the rear differential case bearing.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07150)