Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Separate Seat Type without Inner Belt Attached) › 2016.08–2021.07
RM25T0E _58 Vehicle Interior _029930 SEAT _0289747 FRONT SEAT ASSEMBLY(for Separate Seat Type without Inner Belt Attached) A

SEAT  FRONT SEAT ASSEMBLY(for Separate Seat Type without Inner Belt Attached)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:

If the seat is set down in another location after removing it from the vehicle, the seat may tilt and damage the front inner seat track assembly RH or front outer seat track assembly RH due to the difference in shape between the left and right seat tracks.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is showing the standard bolt chart

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 71148 1.INSTALL FRONT SEAT CUSHION SILENCER

a.

Clean the separate type front seat cushion spring assembly surface.


b.

Install a new 2 front seat cushion silencers as shown in the illustration.

B381153C01
1.781,2.104 1.406,1.25 true 1.771,2.198 2.167,2.594 true 0.719,1.375 1.104,1.865 true 2.458,0.458 1.948,0.24 true 3.083,0.875 3.563,0.313 true 2.875,1.031 2.188,1.365 true 1.771,0.115 2.083,0.313 0.313,0.198 10 false *2 1.302,1.063 1.615,1.26 0.313,0.198 10 false *1 3.552,0.125 3.865,0.323 0.313,0.198 10 false *1 2.229,2.521 2.542,2.719 0.313,0.198 10 false *a 2.021,1.323 2.333,1.521 0.313,0.198 10 false *a 0.542,1.24 0.854,1.438 0.313,0.198 10 false *2
*1 Front Seat Cushion Silencer Pad *2 Separate Type Front Seat Cushion Spring Assembly
*a R end - -


HINT:

Install the front seat cushion silencer pad so that it is aligned with the R end of the separate type front seat cushion spring assembly.



Hide 72053C 2.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH

a.

Install the reclining remote control lever sub-assembly RH with the 2 bolts.


Hide 71511S 3.INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD

a.

Install the separate type front seat cushion pad to the separate type front seat cushion spring assembly.


Hide 71071S 4.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Set the separate type front seat cushion cover in place.


b.
B375327C02
0.417,2.5 1.042,2.219 true 1.656,2.844 1.969,2.417 true 1.938,2.281 2.25,2.479 0.313,0.198 10 false *1 0.26,2.469 0.573,2.667 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 9 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B375328C02
1.906,2.792 2.146,2.198 false 0.719,2.865 1.219,2.281 true 2.115,2.042 2.427,2.24 0.313,0.198 10 false *1 0.552,2.885 0.865,3.083 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


Set the front seat cushion cover with pad in place.


d.

Using hog ring pliers, install the front seat cushion cover with pad to the separate type front seat cushion spring assembly with 11 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the front seat cushion cover with pad.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seat cushion cover with pad.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 72110A 5.INSTALL FRONT OUTER SEAT TRACK ASSEMBLY RH

a.

w/ Seat track adjusting handle:

i.

Temporarily install the front outer seat track assembly RH with the 2 bolts.


ii.

Operate the seat track adjusting handle to move the front outer seat track assembly RH to the foremost position.


iii.

Tighten the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


iv.

Operate the seat track adjusting handle to move the front outer seat track assembly RH to the rearmost position.


v.

Tighten the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)



b.

w/o Seat track adjusting handle:

i.

Temporarily install the front outer seat track assembly RH with the 2 bolts.


ii.

Move the front outer seat track assembly RH to the foremost position.


iii.

Tighten the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


iv.

Move the front outer seat track assembly RH to the rearmost position.


v.

Tighten the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)



Hide 72130A 6.INSTALL FRONT INNER SEAT TRACK ASSEMBLY RH

HINT:

Use the same procedure described for the front outer seat track assembly RH.


Hide 71521A 7.INSTALL FRONT SEAT CUSHION SILENCER PAD (for Walk in Seat Type)

a.
B375317C01
1.615,2.844 1.792,2.135 false 1.75,1.958 2.063,2.156 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the front seat cushion silencer pad with 2 new hog rings as shown in the illustration.


Hide 72510D 8.INSTALL OUTER RECLINING SEAT ADJUSTER ASSEMBLY RH

a.

Install the outer reclining seat adjuster assembly RH to the front seatback frame sub-assembly RH with the 2 bolts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 71551S 9.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the separate type front seatback pad to the front seatback frame sub-assembly RH.


Hide 71073S 10.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.
B375329C03
1.833,2.781 2.094,2.292 true 2.063,2.135 2.375,2.333 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




c.

Attach the 2 hooks to connect the straps of the separate type front seatback cover.


d.
B375330

Pass the straps of the separate type front seatback cover as shown in the illustration.


e.
B375331C02
1.875,2.844 2.146,2.281 true 2.104,2.125 2.417,2.323 0.313,0.198 10 false *1
*1 Hog Ring Pliers


w/o Front Seatback Panel:

Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




f.
B386185C01
1.979,2.802 2.146,2.177 false 2.104,1.99 2.417,2.188 0.313,0.198 10 false *1
*1 Hog Ring Pliers


w/ Front Seatback Panel:

Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




g.

Attach the 4 claws to install the 2 front seat headrest support assemblies.


Hide 74841B 11.INSTALL FRONT SEATBACK PANEL (w/ Front Seatback Panel)

a.

Install the 4 screws and front seatback panel.


Hide 12.INSTALL FRONT SEATBACK ASSEMBLY

a.

Install the center seat hinge spacer to separate type front seatback assembly.


b.

Install the washer to separate type front seat cushion spring assembly.


c.

Install the front seatback assembly with the 2 bolts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


d.

Install a new E-ring.


e.

Lift up the seatback and check that the outer reclining adjuster assembly is fixed in place.


f.

for Walk in Seat Type, for Short Body:

i.
B384186C01
1.021,0.938 0.292,0.292 true 0.115,0.156 0.427,0.354 0.313,0.198 10 false *1
*1 Stake Part


Using pliers, stake the stake part of the front outer seat track assembly RH.


ii.

Tighten the nut to connect the seat track control cable assembly.


iii.

Connect the 2 cables with the clamp to the separate type front seat cushion spring assembly.


iv.

Install the tension spring.



g.

for Walk in Seat Type, for Long Body:

i.

Using pliers, stake the stake part of the front inner seat track assembly RH.


ii.

Tighten the nut to connect the seat track control cable assembly.


iii.

Connect the 2 cables with the clamp to the separate type front seat cushion spring assembly.


iv.

Install the tension spring.



h.
B384187C01
2.885,1.927 1.875,1.208 true 2.969,1.854 3.281,2.052 0.313,0.198 10 false *1
*1 Stake Part


Using pliers, stake the stake part of the outer reclining seat adjuster assembly RH.


i.

Connect the reclining remote control cable with the bolt.


Hide 71811C 13.INSTALL RECLINING ADJUSTER COVER RH

a.

Install the reclining adjuster cover RH with the 2 screws.