Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2016.08–2017.01
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B366892E21
1.479,1.406 1.833,1.594 0.354,0.188 10 false IMI 1.417,0.771 1.771,0.958 0.354,0.188 10 false IMO 0.927,2.104 1.396,2.344 0.469,0.24 10 false ECM 0.927,1.927 2.208,2.167 1.281,0.24 10 false I84*1, A29*2, *3 5.271,1.896 5.74,2.135 0.469,0.24 10 false L30 5.25,2.073 6.667,2.563 1.417,0.49 10 false Transponder Key ECU Assembly 1.792,1.302 2.698,1.521 0.906,0.219 10 false 11 1.792,0.656 2.698,0.875 0.906,0.219 10 false 10 2.708,1.823 4.438,2.177 1.729,0.354 10 false *1: for 1GR-FE, LHD 2.708,2.354 3.896,2.583 1.188,0.229 10 false *3: for 1VD-FTV 5.479,1.417 5.979,1.625 0.5,0.208 10 false EFIO 5.479,0.771 5.979,0.979 0.5,0.208 10 false EFII 5.229,0.656 5.51,0.865 0.281,0.208 10 false 12 5.219,1.302 5.5,1.51 0.281,0.208 10 false 13 2.708,2.115 4.438,2.469 1.729,0.354 10 false *2: for 1GR-FE, RHD

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 61

Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 61 681
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

B

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the I84*1 or A29*2, *3 ECM connector.

*1: for 1GR-FE, LHD

*2: for 1GR-FE, RHD

*3: for 1VD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, LHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - I84-10 (IMO) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
I84-10 (IMO) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - I84-11 (IMI) Always Below 1 Ω
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
I84-11 (IMI) - Body ground Always 10 kΩ or higher

for 1GR-FE, RHD
Tester Connection Condition Specified Condition
L30-12 (EFII) - A29-10 (IMO) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
A29-10 (IMO) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
A29-11 (IMI) - Body ground Always 10 kΩ or higher

for 1VD-FTV
Tester Connection Condition Specified Condition
L30-12 (EFII) - A29-10 (IMO) Always Below 1 Ω
L30-12 (EFII) - Body ground Always 10 kΩ or higher
A29-10 (IMO) - Body ground Always 10 kΩ or higher
L30-13 (EFIO) - A29-11 (IMI) Always Below 1 Ω
L30-13 (EFIO) - Body ground Always 10 kΩ or higher
A29-11 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for SFI System)
NG (for ECD System)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for SFI System)

NG (for ECD System)