| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| SST (attachment) x Cylinder head sub-assembly | 13 | 133 | 10 | |||
| No. 4 water by-pass x No. 2 water by-pass x Cylinder head cover sub-assembly | 10 | 102 | 7 | |||
| No. 4 water by-pass x Timing gear case sub-assembly | 10 | 102 | 7 | |||
| No. 2 engine room wire x No. 3 intake manifold | 13 | 133 | 10 | |||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Service bolt x No. 4 camshaft | 8.0 | 82 | 71 | ||||
| Service bolt x No. 1 camshaft | 8.0 | 82 | 71 | ||||
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| Pump drive shaft gear x No. 1 camshaft timing sprocket x No. 2 camshaft | 24.5 | 250 | 18 | ||||
| Taper screw plug x Timing chain cover sub-assembly | 15 | 153 | 11 | ||||
| No. 4 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 camshaft timing sprocket x No. 3 camshaft | 24.5 | 250 | 18 | ||||
| Taper screw plug x Timing chain cover sub-assembly | 15 | 153 | 11 | ||||
| Engine oil level dipstick guide support x Cylinder head cover sub-assembly RH | 10 | 102 | 7 | ||||
| Engine room main wire x Engine assembly | 10 | 102 | 7 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Service bolt x No. 4 camshaft | 8.0 | 82 | 71 | ||||
| Service bolt x No. 1 camshaft | 8.0 | 82 | 71 | ||||
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| Pump drive shaft gear x No. 1 camshaft timing sprocket x No. 2 camshaft | 24.5 | 250 | 18 | ||||
| Taper screw plug x Timing chain cover sub-assembly | 15 | 153 | 11 | ||||
| No. 4 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 camshaft timing sprocket x No. 3 camshaft | 24.5 | 250 | 18 | ||||
| Taper screw plug x Timing chain cover sub-assembly | 15 | 153 | 11 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Cylinder head sub-assembly RH x Cylinder block sub-assembly | 1st | 80 | 816 | 59 | ||
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| 4th | Turn 90° | |||||
| Cylinder head sub-assembly LH x Cylinder block sub-assembly | 1st | 80 | 816 | 59 | ||
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| 4th | Turn 90° | |||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Cylinder head sub-assembly RH x Cylinder block sub-assembly | 1st | 80 | 816 | 59 | ||
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| 4th | Turn 90° | |||||
| Cylinder head sub-assembly LH x Cylinder block sub-assembly | 1st | 80 | 816 | 59 | ||
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| 4th | Turn 90° | |||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| No. 1 engine hanger x Cylinder head sub-assembly RH | 24.5 | 250 | 18 | ||||
| No. 2 engine hanger x Cylinder head sub-assembly LH | 24.5 | 250 | 18 | ||||
| Rear No. 1 engine mounting insulator x Manual transmission with transfer | 59 | 602 | 44 | ||||
| Front engine mounting insulator LH x Engine mounting stabilizer x Transverse engine mounting bracket LH | 71.5 | 729 | 53 | ||||
| Front engine mounting insulator RH x Engine mounting stabilizer x Transverse engine mounting bracket RH | 71.5 | 729 | 53 | ||||
| Flywheel sub-assembly x Crankshaft | 182 | 1856 | 134 | ||||
| Front engine mounting insulator LH x Flame | 74 | 755 | 55 | ||||
| Front engine mounting insulator RH x Flame | 74 | 755 | 55 | ||||
| No. 2 engine room wire x Timing gear case sub-assembly | 32 | 326 | 24 | ||||
| No. 2 engine room wire x Starter assembly | 21 | 214 | 15 | ||||
| Starter hose bracket sub-assembly x Cylinder head sub-assembly RH | 21 | 214 | 15 | ||||
| Fuel hose bracket x Cylinder head sub-assembly LH (w/ DPF) | 21 | 214 | 15 | ||||
| No. 3 nozzle leakage pipe x Cylinder head sub-assembly RH (w/o DPF) | for union bolt | 21 | 214 | 15 | |||
| for bolt | 10 | 102 | 7 | ||||
| Engine room wire x Engine assembly | 10 | 102 | 7 | ||||
| Engine room wire x Generator assembly (w/o DPF) | 9.8 | 100 | 87 | ||||
| Cooler compressor assembly x Timing chain cover sub-assembly x Timing gear case sub-assembly x Chain cover and compressor bracket sub-assembly | w/ Air Conditioning System | 24 | 245 | 18 | |||
| Vane pump assembly x Timing chain cover sub-assembly | 29 | 296 | 21 | ||||
| Battery carrier sub-assembly x Body | for bolt A | 12.5 | 127 | 9 | |||
| for bolt B | 8.0 | 82 | 71 | ||||
| Fusible link block x Battery carrier sub-assembly | 10 | 102 | 7 | ||||
| Engine wire x Battery carrier sub-assembly | 8.4 | 86 | 74 | ||||
| No. 2 fuse block x Body | 10 | 102 | 7 | ||||
| Battery clamp x Battery carrier sub-assembly | for bolt | 8.0 | 82 | 71 | |||
| for nut | 5.0 | 51 | 44 | ||||
| Hood sub-assembly x Hood hinge | 20 | 204 | 15 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 1 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 4 camshaft bearing cap x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft bearing cap x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 3 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 4 camshaft oil feed pipe sub-assembly x No. 1 camshaft bearing cap | 17 | 173 | 13 | ||||
| No. 2 vacuum transmitting pipe sub-assembly x Timing gear case sub-assembly | 6.0 | 61 | 53 | ||||
| Stud bolt x Timing gear case sub-assembly | for Front Side | 6.0 | 61 | 53 | |||
| for Rear Side | 10 | 102 | 7 | ||||
| Timing gear case sub-assembly x Cylinder block sub-assembly | for 14 mm head bolt (When "dry") The case is "dry" when there is absolutely no engine oil on the 14 mm head bolts and cylinder head set bolt holes. |
46 | 469 | 34 | |||
| for 14 mm head bolt (When "wet") The case is "wet" when there is engine oil on the 14 mm head bolts and cylinder head set bolt holes. |
42 | 428 | 31 | ||||
| for 12 mm head bolt A and B | 29 | 296 | 21 | ||||
| for nut | 29 | 296 | 21 | ||||
| Injection pump drive gear x Injection pump shaft sprocket sub-assembly | 24.5 | 250 | 18 | ||||
| Idle gear thrust plate x No. 1 idle gear x No. 1 idle gear shaft | 47 | 479 | 35 | ||||
| Injection pump drive gear x Fuel supply pump assembly | 68 | 693 | 50 | ||||
| No. 2 camshaft timing sprocket x No. 3 camshaft | 24.5 | 250 | 18 | ||||
| Pump drive shaft gear x No. 1 camshaft timing sprocket x No. 2 camshaft | 24.5 | 250 | 18 | ||||
| No. 2 chain vibration damper x Timing gear case sub-assembly | 21 | 214 | 15 | ||||
| No. 2 chain tensioner assembly x Timing gear case sub-assembly | 10 | 102 | 7 | ||||
| No. 1 chain vibration damper x Timing gear case sub-assembly | 21 | 214 | 15 | ||||
| No. 1 chain tensioner assembly x Timing gear case sub-assembly | 10 | 102 | 7 | ||||
| No. 1 crankshaft position sensor plate x Crankshaft | 10 | 102 | 7 | ||||
| Timing chain cover sub-assembly x Timing gear case sub-assembly | 24.5 | 250 | 18 | ||||
| Crankshaft pulley x Crankshaft | 114.5 | 1168 | 84 | ||||
| No. 1 nozzle holder clamp x Cylinder head sub-assembly RH | w/o DPF | 25 | 255 | 18 | |||
| No. 2 nozzle leakage pipe x Injector assembly | w/o DPF | 18 | 184 | 13 | |||
| No. 2 nozzle leakage pipe x Cylinder head sub-assembly RH | w/o DPF | 21 | 214 | 15 | |||
| Cylinder head cover sub-assembly LH x Cylinder head sub-assembly LH | w/ DPF | 10 | 102 | 7 | |||
| Cylinder head cover sub-assembly RH x Cylinder head sub-assembly RH | w/ DPF | 10 | 102 | 7 | |||
| Stud bolt x Oil pan sub-assembly | 27 mm (1.063 in.) bolt length | 5.2 | 53 | 46 | |||
| 34 mm (1.34 in.) bolt length | 7.5 | 76 | 66 | ||||
| Straight screw plug x Oil pan sub-assembly | using a 10 mm hexagon wrench of straight screw plug | 50 | 510 | 37 | |||
| using a 14 mm hexagon wrench of straight screw plug | 86 | 877 | 63 | ||||
| Turbo oil pipe flange x Oil pan sub-assembly | 10 | 102 | 7 | ||||
| Oil cooler hose drain cock assembly x Oil pan sub-assembly | 20 | 204 | 15 | ||||
| No. 1 oil pan baffle plate x Oil pan sub-assembly | 10 | 102 | 7 | ||||
| Scavenging pump pipe x Oil pan sub-assembly | 10 | 102 | 7 | ||||
| Oil pan drain plug x No. 2 oil pan sub-assembly | 38 | 387 | 28 | ||||
| No. 2 turbo oil pipe x Oil pan sub-assembly | 10 | 102 | 7 | ||||
| Water by-pass pipe sub-assembly x Cylinder block sub-assembly | for union bolt | 35 | 357 | 26 | |||
| for bolt | 10 | 102 | 7 | ||||
| Ventilation tube sub-assembly x Cylinder head sub-assembly LH | 29 | 296 | 21 | ||||
| Ventilation tube sub-assembly x Oil pan sub-assembly | 29 | 296 | 21 | ||||
| No. 2 oil cooler hose clamp x Timing chain cover sub-assembly | 10 | 102 | 7 | ||||
| No. 2 oil cooler hose clamp x V-ribbed belt tensioner assembly | 10 | 102 | 7 | ||||
| Crankshaft position sensor x Timing chain cover sub-assembly | 5.0 | 51 | 44 | ||||
| Camshaft position sensor x Timing chain cover sub-assembly | 5.0 | 51 | 44 | ||||
| Engine oil level dipstick guide support x Cylinder head cover sub-assembly RH | w/ DPF | 10 | 102 | 7 | |||
| Injector lead wire x Cylinder head cover sub-assembly LH | w/ DPF | 10 | 102 | 7 | |||
| Oil filter outlet pipe sub-assembly x Oil pan sub-assembly | 10 | 102 | 7 | ||||
| Transverse engine mounting bracket RH x Cylinder block sub-assembly | 80 | 816 | 59 | ||||
| Transverse engine mounting bracket LH x Cylinder block sub-assembly | 80 | 816 | 59 | ||||
| No. 3 vacuum transmitting pipe sub-assembly x Cylinder block sub-assembly | 6.0 | 61 | 53 | ||||
| No. 3 vacuum transmitting pipe sub-assembly x Oil pan sub-assembly | 6.0 | 61 | 53 | ||||
| Chain cover and compressor bracket sub-assembly x Timing chain cover sub-assembly | 21 | 214 | 15 | ||||
| Idler pulley assembly x Timing chain cover sub-assembly | w/o Air Conditioning System | 24.5 | 250 | 18 | |||
| Idler pulley assembly x Chain cover and compressor bracket sub-assembly | w/o Air Conditioning System | 24.5 | 250 | 18 | |||
| No. 2 exhaust manifold heat insulator x Exhaust manifold LH | 25 | 255 | 18 | ||||
| No. 1 water outlet pipe x No. 2 water outlet pipe | 21 | 214 | 15 | ||||
| No. 1 water outlet pipe x Cylinder head sub-assembly LH | 21 | 214 | 15 | ||||
| Water by-pass outlet sub-assembly x Cylinder head sub-assembly RH | 21 | 214 | 15 | ||||
| Water outlet x Engine water pump assembly | 21 | 214 | 15 | ||||
| No. 3 engine hanger x Timing gear case sub-assembly | 43 | 438 | 32 | ||||
| Intercooler support bracket x No. 3 engine hanger | 21 | 214 | 15 | ||||
| No. 2 intercooler support bracket x Timing gear case sub-assembly | 43 | 438 | 32 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Cylinder head stud bolt x Cylinder head sub-assembly | 12 | 122 | 9 | |||
| No. 1 straight screw plug with head x Cylinder head sub-assembly | 25 | 255 | 18 | |||
| No. 1 straight screw plug with head x Cylinder head sub-assembly | w/ DPF | 18 | 184 | 13 | ||
| Nozzle holder clamp seat x Cylinder head sub-assembly | w/o DPF | 10 | 102 | 7 | ||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Cylinder block straight screw plug x Cylinder block sub-assembly | 38 | 387 | 28 | |||
| Cylinder block stud bolt x Cylinder block sub-assembly | using an E7 "TORX" wrench of cylinder block stud bolt | 10 | 102 | 7 | ||
| using an E8 "TORX" wrench of cylinder block stud bolt | 10 | 102 | 7 | |||
| No. 1 oil nozzle sub-assembly x Cylinder block sub-assembly | 10 | 102 | 7 | |||
| Cylinder block stiffening plate x Crankshaft bearing cap x Cylinder block sub-assembly | for bolt A 11 mm (0.433 in.) diameter x 106 mm (4.17 in.) bolt length |
1st | 35 | 357 | 26 | |
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| for bolt B 10 mm (0.394 in.) diameter x 90.5 mm (3.56 in.) bolt length |
1st | 60 | 612 | 44 | ||
| 2nd | Turn 90° | |||||
| for bolt C 10 mm (0.394 in.) diameter x 22 mm (0.866 in.) bolt length |
56 | 571 | 41 | |||
| Connecting rod cap x Connecting rod | 1st | 35 | 357 | 26 | ||
| 2nd | Turn 90° | |||||
"TORX" is a registered trademark of Textron Inc..