Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top) › from 2016.08
RM25T0E _59 Vehicle Exterior _029940 LIGHTING (EXT) _0138216 REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top) A

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81565 1.INSTALL REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH (for Rear Body Side)

a.

Attach the wire harness clamp to install the rear combination light socket and wire sub-assembly LH to the rear combination light lens LH.


Hide 81566 2.INSTALL REAR COMBINATION LIGHT RIM LH (for Rear Bumper Side)

a.

Install the rear combination light rim LH to the rear combination light body LH with the 3 screws.


Hide 81567B 3.INSTALL REAR COMBINATION LIGHT PROTECTOR LH (for Rear Bumper Side)

a.

Install the rear combination light protector LH to the rear combination light body LH with the screw.


Hide 81569A 4.INSTALL REAR COMBINATION LIGHT BRACKET LH (for Rear Bumper Side, w/ Bracket)

a.

Install the rear combination light bracket LH to the rear combination light body LH with the screw.


b.

Attach the wire harness clamp.


Hide 81562A 5.INSTALL REAR COMBINATION LIGHT GASKET LH (for Rear Bumper Side)

a.
E298640C02
1.146,2.031 1.375,2.24 0.229,0.208 10 true *a
*a Notch


Install a new rear combination light lens gasket LH to the rear combination light body LH.

NOTICE:

Position the notch of the rear combination light lens gasket LH at the lower center of the rear combination light body LH.



Hide 81550D 6.INSTALL REAR COMBINATION LIGHT BULB (for Rear Turn Signal Light)

a.

for Rear Body Side:

i.
E296856C04
1,1.104 1.427,1.104 false 1.948,1.104 2.375,1.104 false 0.802,1 1.115,1.156 0.313,0.156 10 false *a 2.438,1 2.75,1.156 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the side turn signal light bulb with the 2 cutouts of the bulb socket and insert the bulb to the bulb socket.


ii.
E296854C01
0,0 0,0 false
V100135

Push
V100137

Clockwise


While pushing the side turn signal light bulb, turn the bulb clockwise to install the bulb.


iii.
E296852C02
1.25,1.219 1.031,0.458 1.031,0.458 0.625,0.458 true 2.104,0.542 1.844,0.542 1.844,0.542 1.844,1.083 true 0.427,0.365 0.74,0.563 0.313,0.198 10 false *a 2.156,0.448 2.365,0.635 0.208,0.188 10 true *b
*a Base Point
*b Unlock Position Mark


Align the base point of the bulb socket to the unlock position mark.


iv.
E298633

Rotate the bulb socket clockwise until the lock to connect it to the rear combination light lens LH.



b.

for Rear Bumper Side:

i.
E296841C02
0.969,1.146 1.438,1.146 false 1.979,1.146 2.448,1.146 false 0.76,1.042 1.073,1.198 0.313,0.156 10 false *a 2.5,1.052 2.813,1.208 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the rear combination light bulb with the 2 cutouts of the bulb socket and insert the bulb to the rear combination light body LH.


ii.
E298638C01
0,0 0,0 false
V100135

Push
V100136

Clockwise


While pushing the rear combination light bulb in the direction indicated by the white arrow shown in the illustration, turn the bulb clockwise to install the bulb.



Hide 81550D 7.INSTALL REAR COMBINATION LIGHT BULB (for Backup Light)

a.
E296856C04
1,1.104 1.427,1.104 false 1.948,1.104 2.375,1.104 false 0.802,1 1.115,1.156 0.313,0.156 10 false *a 2.438,1 2.75,1.156 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the rear combination light bulb with the 2 cutouts of the bulb socket and insert the bulb to the bulb socket.


b.
E296854C01
0,0 0,0 false
V100135

Push
V100137

Clockwise


While pushing the rear combination light bulb, turn the bulb clockwise to install the bulb.


c.
E296851C02
1.469,1.031 1.625,0.479 1.625,0.479 1.875,0.479 true 1.896,0.979 1.896,1.583 1.896,1.583 2.156,1.583 true 1.938,0.375 2.25,0.531 0.313,0.156 10 false *a 2.229,1.479 2.542,1.635 0.313,0.156 10 false *b
*a Base Point
*b Unlock Position Mark


Align the base point of the bulb socket to the unlock position mark.


d.
E298632

Rotate the bulb socket clockwise until the lock to connect it to the rear combination light lens LH.


Hide 81550B 8.INSTALL REAR COMBINATION LIGHT BULB (for Tail and Stop Light)

a.

for Rear Body Side:

i.
E296855C02
0.927,1.135 1.427,1.135 false 2.135,1 2.635,1 false 2.698,0.906 3.01,1.063 0.313,0.156 10 false *a 0.74,1.042 1.052,1.198 0.313,0.156 10 false *b
*a Upper Protrusion
*b Lower Protrusion
V100136

Long Cutout
V100137

Short Cutout


Align the upper protrusion of the rear combination light bulb with the short cutout of the bulb socket and the lower protrusion with the long cutout, and then insert the bulb to the bulb socket.


ii.
E296854C01
0,0 0,0 false
V100135

Push
V100137

Clockwise


While pushing the rear combination light bulb, turn the bulb clockwise to install the bulb.


iii.
E296850C02
1.354,1.135 0.948,0.552 0.948,0.552 0.448,0.552 true 2.146,1.573 1.76,1.573 1.76,1.573 1.76,1.073 true 0.219,0.458 0.531,0.615 0.313,0.156 10 false *a 2.219,1.469 2.531,1.625 0.313,0.156 10 false *b
*a Base Point
*b Unlock Position Mark


Align the base point of the bulb socket to the unlock position mark.


iv.
E296849

Rotate the bulb socket clockwise until the lock to connect it to the rear combination light lens LH.



b.

for Rear Bumper Side:

i.
E296842C02
0.813,1.219 1.365,1.219 false 2.063,1.083 2.615,1.083 false 2.667,0.969 2.979,1.125 0.313,0.156 10 false *a 0.625,1.115 0.938,1.271 0.313,0.156 10 false *b
*a Upper Protrusion
*b Lower Protrusion
V100136

Long Cutout
V100137

Short Cutout


Align the upper protrusion of the rear combination light bulb with the short cutout of the rear combination light body LH and the lower protrusion with the long cutout, and then insert the bulb to the rear combination light body LH.


ii.
E298635C01
0,0 0,0 false
V100135

Push
V100136

Clockwise


While pushing the rear combination light bulb, turn the bulb clockwise to install the bulb.



Hide 81561A 9.INSTALL REAR COMBINATION LIGHT LENS LH (for Rear Bumper Side)

a.

Install the rear combination light lens LH to the rear combination light body LH with the 2 screws.