Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2017.01
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0306275 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the wheels are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

Initialization is normally completed within a few minutes.

·

It may take up to a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21

·

If initialization has not been completed successfully, DTC C2177/77 is stored after a vehicle speed of 40 km/h (25 mph) or more continues for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·

While the answer-back function for the ID switching function is operating, the system will not change to initialization mode even if the initialization procedure is performed.

·
C217594C05
1.802,1.427 2.052,1.76 false 1.76,0.292 1.604,0.896 false 0.156,0.083 0.833,0.365 0.677,0.281 10 *a 1.969,1.792 2.49,1.969 0.521,0.177 10 TC 1.688,0.125 2.042,0.302 0.354,0.177 10 CG
*a Front view of DLC3


Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



BEFORE INITIALIZATION


a.

Set the tire pressure to the specified value.

HINT:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION




INITIALIZATION PROCEDURE


HINT:

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

·

Due to the operation of the tire pressure warning reset switch, the tire pressure drops to approximately 75% or less of the tire pressure set during system initialization.

·

The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 75% or less of the tire pressure* when the tires are warmed.

*: If initialization is performed and the vehicle is driven for a certain period of time, the tire pressure set during system initialization is adjusted and set to the tire pressure when the tires are warmed from the driving conditions.

NOTICE:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 75% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 75% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




a.

Turn the ignition switch to ON.


b.
C373220C01
0.292,0.542 0.604,0.698 0.313,0.156 10 false *1 2.469,2.667 2.781,2.823 0.313,0.156 10 false *2 0.167,2.948 0.479,3.104 0.313,0.156 10 false *a 0.146,3.563 0.458,3.719 0.313,0.156 10 false *c 0.177,3.813 0.49,3.969 0.313,0.156 10 false *d 1.188,3.156 1.5,3.313 0.313,0.156 10 false *b 0.917,4.063 1.229,4.219 0.313,0.156 10 false *b
*1 Tire Pressure Warning Light
*2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.


c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

for Short Body with Tire Size 265/70R16:

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 42 84,85,86,87,88

except Short Body with Tire Size 265/70R16:

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 42 99,100,101,102,103

g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.