Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › from 2017.01
RM25T0E _52 Drivetrain _029901 CLUTCH _0136564 CLUTCH PEDAL(for LHD) N

CLUTCH  CLUTCH PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 31301 1.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

a.
C370418C02
1.917,1.083 2.333,0.833 2.333,0.833 2.583,0.833 false 0.75,2.583 1,2.583 1,2.583 1.417,1.583 false 2.688,3.76 3,3.917 0.313,0.156 10 false *a 2.667,0.76 2.896,0.917 0.229,0.156 10 false *b 0.583,2.5 0.813,2.667 0.229,0.167 10 false *c
*a Pedal Height
*b Pedal Height Adjustment Point
*c Push Rod Play Adjustment Point


Check that the pedal height is correct.

Standard pedal height from floor panel:

179.2 to 189.2 mm (7.06 to 7.44 in.)



b.

Adjust the pedal height.

i.

for 1VD-FTV:

Loosen the lock nut and turn the clutch switch assembly until the height is correct. Tighten the lock nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


ii.

for 1GR-FE, 1HZ:

Loosen the lock nut and turn clutch pedal stopper bolt until height is correct. Tighten the lock nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)



c.
D031462C08
1.833,1.615 2.031,1.76 0.198,0.146 10 false *a 1.875,1.927 2.083,2.083 0.208,0.156 10 false *b
*a Push Rod Play
*b Pedal Free Play


Check that the pedal free play and push rod play are correct.

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.

Depress the pedal until the clutch resistance begins to be felt.

Standard pedal free play:

5.0 to 15.0 mm (0.197 to 0.590 in.)



ii.

Gently depress the pedal until the resistance begins to increase a little.

Standard push rod play at pedal top:

1.0 to 5.0 mm (0.0394 to 0.1968 in.)




d.

Adjust the pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the pedal free play and push rod play are correct.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


iii.

After adjusting the pedal free play and push rod play, check the pedal height.

Standard pedal height from floor panel:

179.2 to 189.2 mm (7.06 to 7.44 in.)




e.
C227877C09
1.365,1.177 1.615,1.177 false 1.615,1.583 2.281,1.042 2.281,1.042 2.396,1.042 true 1.354,1.521 0.906,1.885 0.906,1.885 0.802,1.885 true 1.781,1.896 2.021,2.104 0.24,0.208 10 false *c 0.594,1.802 0.854,2.01 0.26,0.208 10 false *d 2.438,0.927 2.74,1.177 0.302,0.25 10 false *b 1.385,0.958 1.646,1.188 0.26,0.229 10 false *a
*a 25 mm (0.984 in.) or more
*b Release Point
*c Pedal Stroke
*d Full Stroke End Position


Check the clutch release point.

i.

Pull the parking brake lever and chock the wheels.


ii.

Start the engine and allow it to idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever in to the reverse position until the gears engage.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance from pedal stroke end position to release point:

25 mm (0.984 in.) or higher


If the distance is not as specified, perform the following operations:

·

Check the pedal height.

·

Check the push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover and disc.