Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with VSC) › from 2017.01
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306319 CAN COMMUNICATION SYSTEM(for RHD with VSC) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with VSC)  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) operates. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.


b.

Effects on each system when communication is impossible (for further details, see the pages for each system).

Function
1.

Control Master

2.

System Related

3.

Control Actuator


Fail-safe Function System Behavior Indicator and Buzzer Behavior or User Notification DTC Detection
(ECU that stored DTC)
TC DTC Output Service
(While TC = ON is being received, a DTC is output in response to a request from the combination meter assembly.)
1.

Combination meter assembly

2.

ECM

3.

Airbag sensor assembly


When reception of the TC signal is lost during the TC service (TC = ON), this is regarded as TC = OFF and the TC service ends. Nothing -
Collision Detection Signal
(Reports a collision in order to perform a fuel cut, etc. during a collision.)
1.

ECM

2.

Airbag sensor assembly

3.

-


Nothing Nothing -
Airbag Warning Light Control
(Sends airbag warning light illumination information.)
1.

Combination meter assembly

2.

Airbag sensor assembly

3.

-


Nothing Nothing -
Trigger Signal/Autonomous Transmission
(Outputs the yaw rate and acceleration sensor signal.)
1.

Airbag sensor assembly

2.

Brake actuator assembly (skid control ECU)

3.

Brake actuator assembly (skid control ECU)


Sends yaw rate sensor data information. Nothing -
Event Data Recorder (EDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.)
1.

Airbag sensor assembly

2.

ECM, Brake actuator assembly (skid control ECU), Combination meter assembly, Spiral with sensor cable sub-assembly (steering angle sensor)

3.

-


·

When there is a communication error, a failure notification is received from the other device, or an invalid value is recorded in the EDR when the communication failure occurs.

·

When there is a periodic problem, the previous value is maintained.


Nothing -
Steering Sensor
(Detects steering wheel angle)
1.

Spiral with sensor cable sub-assembly (steering angle sensor)

2.

Brake actuator assembly (skid control ECU)

3.

-


Sends steering sensor data information every 0.012 seconds. Nothing -
Speedometer
(Operates the speedometer according to the vehicle speed signals from the skid control ECU.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "0". Displays 0 km/h (0 mph) in the speedometer. U0129
(Combination meter assembly)
Tachometer
(Displays the tachometer.)
1.

Combination meter assembly

2.

ECM

3.

-


Signal is considered to be "0". Displays 0 rpm in the tachometer. U0100
(Combination meter assembly)
Fuel Gauge
·

Displays the fuel gauge fuel level.

·

Turns the remaining fuel amount warning on and off.


1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "0". Calculation continues using a provisional value. U0129
(Combination meter assembly)
Sub Fuel Gauge
(Displays the fuel gauge fuel level.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "0". Calculation continues using a provisional value. U0129
(Combination meter assembly)
Engine Coolant Temperature Gauge
(Display operates the engine coolant temperature gauge.)
1.

Combination meter assembly

2.

ECM

3.

-


Signal is considered to be "0". The needle of the engine coolant temperature gauge is at the C mark or below. -
ODO/TRIP Meter
(Displays the ODO/TRIP meter.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "0". The last displayed value remains. U0129
(Combination meter assembly)
SRS Warning Light
(Displays SRS warning light.)
1.

Combination meter assembly

2.

Airbag sensor assembly

3.

-


Signal is considered to be "Active". The SRS warning light illuminates. U0151
(Combination meter assembly)
ABS Warning Light
(Displays ABS warning light.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "Active". The ABS warning light illuminates. U0129
(Combination meter assembly)
Brake Warning Light
(Displays brake warning light.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "Active". The brake warning light illuminates. U0129
(Combination meter assembly)
SLIP Indicator Light
(Displays SLIP indicator light.)
1.

Combination meter assembly

2.

Brake actuator assembly (skid control ECU)

3.

-


Signal is considered to be "Active". The SLIP indicator light illuminates. U0129
(Combination meter assembly)
Cruise Control
(Adjusts the engine throttle valve opening amount automatically to control the vehicle.)
1.

ECM

2.

Brake actuator assembly (skid control ECU), Combination meter assembly

3.

ECM


Cruise control does not operate. The cruise indicator light illuminates in yellow. -
Anti-lock Brake System Control
(Prevents the wheels from locking during sudden stops.)
1.

Brake actuator assembly (skid control ECU)

2.

Airbag sensor assembly

3.

Brake actuator assembly (skid control ECU)


·

During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control.

·

Not during control: Control cannot begin.


·

The ABS warning light illuminates.

·

The SLIP indicator illuminates.


·

U0073

·

U0124


(Brake actuator assembly [skid control ECU])
Vehicle Stability Control/Traction Control/Vehicle Dynamics Integrated Management Control
(Suppresses vehicle instability, such as drift when cornering and wheel slippage when accelerating. During vehicle dynamics integrated management control, vehicle integrated control which includes electronic steering control is performed.)
1.

Brake actuator assembly (skid control ECU)

2.

ECM, Airbag sensor assembly, Spiral with sensor cable sub-assembly (steering angle sensor)

3.

Brake actuator assembly (skid control ECU)


·

During control: After ending backup control (which stabilizes the vehicle), the system changes to normal braking and prohibits this control.

·

Not during control: Control cannot begin.


·

The ABS warning light illuminates.

·

The SLIP indicator illuminates.


·

U0073

·

U0124


(Brake actuator assembly [skid control ECU])