Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with VSC) › 2017.01–2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306319 CAN COMMUNICATION SYSTEM(for RHD with VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with VSC)  Short to GND in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
·

Short between CAN bus lines and GND

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Airbag sensor assembly

·

Combination meter assembly

·

No. 4 CAN junction connector

·

No. 5 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C363468E01
6.01,0.427 6.625,0.625 0.615,0.198 10 false CANH 6.021,1.188 6.635,1.385 0.615,0.198 10 false CANL 0.76,1.063 1.375,1.26 0.615,0.198 10 false CANL 0.729,0.531 1.344,0.729 0.615,0.198 10 false CANH 1.271,0.448 1.885,0.646 0.615,0.198 10 false 22 1.26,0.969 1.875,1.167 0.615,0.198 10 false 10 0.156,1.448 0.771,1.646 0.615,0.198 10 false A42 0.146,1.604 1.76,1.969 1.615,0.365 10 false Brake Actuator Assembly (Skid Control ECU) 6.198,1.49 6.885,1.844 0.688,0.354 10 false A29 6.198,1.635 6.885,1.99 0.688,0.354 10 false ECM 3.865,1.51 4.552,1.865 0.688,0.354 10 false 6 3.865,2.063 4.552,2.417 0.688,0.354 10 false 12 2.948,0.469 3.635,0.823 0.688,0.354 10 false 4 2.885,0.99 3.573,1.344 0.688,0.354 10 false 10 3.854,0.979 4.542,1.333 0.688,0.354 10 false 9 3.865,0.458 4.552,0.813 0.688,0.354 10 false 3 5.75,0.458 6.438,0.813 0.688,0.354 10 false 41 5.74,0.979 6.427,1.333 0.688,0.354 10 false 49 2.615,2.542 5.146,2.896 2.531,0.354 10 false I111 2.604,2.688 5.135,3.042 2.531,0.354 10 false No. 5 CAN Junction Connector 0.729,3.354 1.344,3.552 0.615,0.198 10 false CANH 0.76,3.885 1.375,4.083 0.615,0.198 10 false CANL 0.74,5.74 1.354,5.938 0.615,0.198 10 false CANL 6.01,5.74 6.625,5.938 0.615,0.198 10 false CANL 6,7.823 6.615,8.021 0.615,0.198 10 false CANL 0.719,5.229 1.333,5.427 0.615,0.198 10 false CANH 6.01,5.229 6.625,5.427 0.615,0.198 10 false CANH 6.01,7.052 6.625,7.25 0.615,0.198 10 false CANH 1.26,3.24 1.948,3.594 0.688,0.354 10 false 6 1.271,3.76 1.958,4.115 0.688,0.354 10 false 14 0.448,4.281 2.063,4.646 1.615,0.365 10 false I17 0.448,4.448 2.063,4.813 1.615,0.365 10 false DLC3 3.969,3.115 4.656,3.469 0.688,0.354 10 false 1 2.823,3.115 3.51,3.469 0.688,0.354 10 false 1 2.823,4.99 3.51,5.344 0.688,0.354 10 false 1 3.99,4.99 4.677,5.344 0.688,0.354 10 false 1 5.708,7.042 6.396,7.396 0.688,0.354 10 false 13 5.708,7.563 6.396,7.917 0.688,0.354 10 false 14 5.135,8.104 7.052,8.313 1.917,0.208 10 false L26 5.125,8.26 7.042,8.469 1.917,0.208 10 false Combination Meter Assembly 0.219,6.135 1.833,6.5 1.615,0.365 10 false I51 0.219,6.281 1.833,6.646 1.615,0.365 10 false Airbag Sensor Assembly 1.25,5.677 2.865,6.042 1.615,0.365 10 false 22 1.26,5.115 2.875,5.479 1.615,0.365 10 false 13 2.823,5.542 4.438,5.906 1.615,0.365 10 false 2 3.979,5.552 5.594,5.917 1.615,0.365 10 false 2 3.969,3.656 5.583,4.021 1.615,0.365 10 false 2 2.823,3.656 4.438,4.021 1.615,0.365 10 false 2 5.813,5.646 6.458,6.083 0.646,0.438 10 false 3 4.583,6.146 7.031,6.531 2.448,0.385 10 false L47 4.573,6.292 7.021,6.677 2.448,0.385 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 5.792,5.135 6.438,5.573 0.646,0.438 10 false 4 2.615,8.146 5.146,8.5 2.531,0.354 10 false No. 4 CAN Junction Connector 3.958,7.458 5.573,7.823 1.615,0.365 10 false 2 3.979,6.938 4.667,7.292 0.688,0.354 10 false 1 3.865,7.156 4.552,7.51 0.688,0.354 10 false I112 3.875,7.688 4.563,8.042 0.688,0.354 10 false I112 3.885,5.24 4.573,5.594 0.688,0.354 10 false I114 2.729,3.354 3.417,3.708 0.688,0.354 10 false I113 2.719,5.76 3.406,6.115 0.688,0.354 10 false I116 2.729,3.885 3.417,4.24 0.688,0.354 10 false I113 3.865,3.885 4.552,4.24 0.688,0.354 10 false I115 3.875,3.365 4.563,3.719 0.688,0.354 10 false I115 3.885,5.76 4.573,6.115 0.688,0.354 10 false I114 2.719,5.24 3.406,5.594 0.688,0.354 10 false I116

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C363471C05
1.635,0.552 2.146,0.76 0.51,0.208 5.01,0.656 5.521,0.865 0.51,0.208 1.781,1.51 1.188,1.042 1.188,1.042 0.927,1.042 true 1.792,1.74 1.302,2.177 1.302,2.177 1.042,2.177 true 2.771,1.313 2.583,1.313 2.583,1.313 2.25,1.479 true 2.688,0.854 2.5,0.854 2.5,0.854 1.927,1.49 true 2.688,2.094 2.5,2.094 2.5,2.094 2.24,1.75 true 2.417,2.385 2.229,2.385 2.229,2.385 1.948,1.75 true 5.24,1.292 4.792,0.896 4.792,0.896 4.531,0.896 true 0.25,0.229 0.563,0.385 0.313,0.156 10 false *a 4.01,0.313 4.323,0.469 0.313,0.156 10 false *b 1.74,0.552 2.25,0.865 0.51,0.313 10 false I111 0.375,0.917 1.104,1.198 0.729,0.281 10 false CANH*c 0.49,2.073 1.219,2.354 0.729,0.281 10 false CANL*c 5.177,0.677 5.698,0.99 0.521,0.313 10 false I17 4.281,0.76 4.594,0.979 0.313,0.219 10 false CG 2.469,2.26 3.198,2.542 0.729,0.281 10 false CANL*d 2.76,1.99 3.49,2.271 0.729,0.281 10 false CANL*e 2.833,1.219 3.563,1.5 0.729,0.281 10 false CANH*e 2.74,0.76 3.469,1.042 0.729,0.281 10 false CANH*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b Front view of DLC3
*c to ECM *d to Brake Actuator Assembly (Skid Control ECU)
*e to No. 4 CAN Junction Connector - -



b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
I111-3 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
I111-9 (CANL) - I17-4 (CG)
I111-4 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)
I111-10 (CANL) - I17-4 (CG)
I111-6 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 4 CAN junction connector
I111-12 (CANL) - I17-4 (CG)



Result:
Result Proceed to
OK A
NG (to No. 4 CAN junction connector CAN main wire) B
NG (ECU or sensor CAN wires) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the I111 No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connectors.

C363470C03
4,2.75 4.625,3.031 0.625,0.281 1.344,2.781 1.604,2.552 1.604,2.552 1.823,2.552 true 1.333,2.938 1.552,3.25 1.552,3.25 1.771,3.25 true 5.042,2.292 5.24,2.292 5.24,2.292 5.563,2.656 true 4.208,2.781 4.667,2.979 0.458,0.198 10 false I17 1.844,2.427 2.302,2.625 0.458,0.198 10 false CANH 1.813,3.125 2.271,3.323 0.458,0.198 10 false CANL 4.781,2.167 5.24,2.365 0.458,0.198 10 false CG 3.885,2.115 4.344,2.313 0.458,0.198 10 false *b 0.344,2.188 0.802,2.385 0.458,0.198 10 false *a 0.302,0.125 0.76,0.323 0.458,0.198 10 false *1 3.74,1.698 4.198,1.896 0.458,0.198 10 false I112 3.719,1.406 4.177,1.604 0.458,0.198 10 false I114 2.177,1.406 2.635,1.604 0.458,0.198 10 false I113 2.167,1.125 2.625,1.323 0.458,0.198 10 false I115 2.156,0.844 2.615,1.042 0.458,0.198 10 false I116
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


No. 4 CAN Junction Connector Wiring Color Connect to
I112-1 (CANH) G Combination meter assembly
I112-2 (CANL) W
I113-1 (CANH) L DLC3
I113-2 (CANL) W
I114-1 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
I114-2 (CANL) W
I115-1 (CANH) B No. 5 CAN junction connector
I115-2 (CANL) W
I116-1 (CANH) P Airbag sensor assembly
I116-2 (CANL) W


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
I112-1 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
I112-2 (CANL) - I17-4 (CG)
I113-1 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
I113-2 (CANL) - I17-4 (CG)
I114-1 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with sensor cable sub-assembly (steering angle sensor)
I114-2 (CANL) - I17-4 (CG)
I115-1 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 5 CAN junction connector
I115-2 (CANL) - I17-4 (CG)
I116-1 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
I116-2 (CANL) - I17-4 (CG)



Result:
Result Proceed to
OK A
NG (to DLC3 CAN branch wire) B
NG (to No. 5 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN wires) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

D

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C300827C57
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 2.156,0.385 2.156,0.385 2.365,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 1.594,0.906 1.344,0.479 1.344,0.479 1.167,0.479 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.208,1.021 0.542,1.219 0.333,0.198 10 false I17 2.427,0.281 2.917,0.427 0.49,0.146 10 false CANH 1.177,1.792 1.792,1.99 0.615,0.198 10 false CANL 0.917,0.365 1.26,0.521 0.344,0.156 10 false CG
*a Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-6 (CANH) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-14 (CANL) - I17-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN WIRES OR CONNECTOR