Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with VSC) › 2017.01–2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306321 CAN COMMUNICATION SYSTEM(for LHD with VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with VSC)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of spiral with sensor cable sub-assembly (steering angle sensor)

·

Spiral with sensor cable sub-assembly (steering angle sensor) ground circuit

·

Spiral with sensor cable sub-assembly (steering angle sensor) CAN branch wire or connector

·

Spiral with sensor cable sub-assembly (steering angle sensor)



WIRING DIAGRAM

C240994E07
4.646,3.948 5.219,4.271 0.573,0.323 10 false L47 4.615,4.094 7.073,4.448 2.458,0.354 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 5.75,1.094 6.167,1.271 0.417,0.177 10 false CANL 5.75,0.563 6.156,0.75 0.406,0.188 10 false CANH 5.563,0.469 5.677,0.625 0.115,0.156 10 false 4 5.563,0.99 5.719,1.135 0.156,0.146 10 false 3 5.75,3.156 6.177,3.333 0.427,0.177 10 false ESS 5.771,2.635 6.177,2.823 0.406,0.188 10 false IG 5.76,2.125 6.156,2.281 0.396,0.156 10 false BAT 5.563,2.01 5.677,2.167 0.115,0.156 10 false 6 5.552,2.521 5.656,2.677 0.104,0.156 10 false 5 5.552,3.031 5.656,3.188 0.104,0.156 10 false 2 1.604,0.469 1.76,0.635 0.156,0.167 10 false 1 1.615,0.979 1.844,1.125 0.229,0.146 10 false 2 0.5,1.385 0.833,1.531 0.333,0.146 10 false I121 0.51,1.552 2.75,1.802 2.24,0.25 10 false No. 6 CAN Junction Connector 1.708,2.052 2.698,2.354 0.99,0.302 10 false from Battery 1.396,2.583 2.771,2.865 1.375,0.281 10 false from IG1 1 Relay 3.823,2.823 4.906,2.99 1.083,0.167 10 false ECU IG 3.823,2.271 4.302,2.448 0.479,0.177 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
C234977C10
0.479,1.052 1.063,1.323 0.583,0.271 1.813,1.302 2.177,1.781 2.177,1.781 2.292,1.781 true 1.635,1.271 1.292,1.74 1.292,1.74 1.188,1.74 true 0.615,1.073 0.99,1.302 0.375,0.229 10 false L47 0.781,1.646 1.208,1.813 0.427,0.167 10 false CANH 2.354,1.677 2.75,1.854 0.396,0.177 10 false CANL 0.188,0.104 0.49,0.271 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-4 (CANH) - L47-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
C234977C09
2.417,1.031 2.969,1.313 0.552,0.281 1.927,1.323 2.198,1.781 2.198,1.781 2.302,1.781 true 1.406,1.208 1.188,0.938 1.188,0.938 1.042,0.938 true 1.542,1.313 1.208,1.792 1.208,1.792 1.042,1.792 true 2.552,1.073 2.885,1.219 0.333,0.146 10 false L47 0.75,0.833 1.063,0.979 0.313,0.146 10 false BAT 0.833,1.667 1.052,1.833 0.219,0.167 10 false IG 2.354,1.677 2.802,1.938 0.448,0.26 10 false ESS 0.073,0.031 0.375,0.198 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-6 (BAT) - Body ground Always 11 to 14 V
L47-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR