The skid control ECU (brake actuator assembly) receives the signals from the ECM, steering angle sensor (spiral with sensor cable sub-assembly) and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | Any of the following is detected:
1.
A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.)
2.
When the +BS terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more.
3.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.
-
The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds. |
CAN communication system |
| U0100 | Lost Communication with ECM | When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more. |
·
CAN communication system
·
Skid control ECU (Brake actuator assembly)
·
ECM |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | Either of the following is detected:
1.
When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more.
2.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.
-
The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds. |
·
CAN communication system
·
Skid control ECU (Brake actuator assembly)
·
Acceleration sensor (Airbag sensor assembly) |
| U0126 | Lost Communication with Steering Angle Sensor Module | Either of the following is detected:
1.
When the +BS terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.
2.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.
-
The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds. |
·
CAN communication system
·
Skid control ECU (Brake actuator assembly)
·
Steering angle sensor |
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| EFI Communication Open | ECM communication open detection | Normal or Error | Normal | Error: Momentary interruption |
| Yaw Rate Open | Yaw rate sensor open detection | Normal or Error | Normal | Error: Momentary interruption |
| Deceleration Open | Acceleration sensor open detection | Error or Normal | Normal | Error: Momentary interruption |
| Steering Open | Steering angle sensor open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| EFI Communication Open |
| Yaw Rate Open |
| Deceleration Open |
| Steering Open |
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| There is a constant open circuit |
| There are no momentary interruptions |
| There are momentary interruptions |
There is a constant open circuit
There are no momentary interruptions
There are momentary interruptions
Turn the ignition switch off.
Check if each sensor or ECM connector is securely connected.
Each connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Record the output DTCs (for VSC system and/or CAN communication system).
for VSC system: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM
If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for VSC system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| DTC (relating to CAN communication system) is output | A |
| DTC (relating to VSC system) is output | B |
| DTC is not output | C |
A
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM.
Check that there is no momentary interruption.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.
Check that no CAN communication system DTC is output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM
If VSC system DTCs are output, record them.
The CAN communication system must be normal when repairing each sensor DTC (for VSC system).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (relating to VSC system) | B |
| DTC is output (relating to CAN communication system) | C |
A
B
C
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING