Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DIAGNOSIS SYSTEM

WIRING DIAGRAM

C274777E92
0.865,1.26 1.479,1.458 0.615,0.198 10 false CANL 1.333,1.073 1.646,1.271 0.313,0.198 10 false 14 5.844,1.073 6.156,1.271 0.313,0.198 10 false 10 6.115,1.25 6.729,1.448 0.615,0.198 10 false CANL 0.844,2.302 1.458,2.5 0.615,0.198 10 false CANH 1.323,2.125 1.635,2.323 0.313,0.198 10 false 13 5.844,2.115 6.156,2.313 0.313,0.198 10 false 22 6.104,2.323 6.719,2.521 0.615,0.198 10 false CANH 2.375,3.344 3.344,3.604 0.969,0.26 10 false from IG Circuit 4.469,3.5 5.094,3.719 0.625,0.219 10 false ECU IG 5.833,3.229 6.146,3.427 0.313,0.198 10 false 12 6.115,3.344 6.573,3.542 0.458,0.198 10 false IG1 5.854,4.281 6.167,4.479 0.313,0.198 10 false 25 6.115,4.406 6.729,4.604 0.615,0.198 10 false GND1 2.76,6.396 4.479,6.625 1.719,0.229 10 false : CAN Communication Line 0.281,5.938 0.594,6.135 0.313,0.198 10 false L26 0.292,6.104 1.5,6.531 1.208,0.427 10 false Combination Meter Assembly 5.635,5.927 5.948,6.125 0.313,0.198 10 false A42 5.615,6.115 7.156,6.604 1.542,0.49 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C364797C06
1.542,0.104 1.917,0.333 0.375,0.229 2.906,1.854 2.906,1.375 2.906,1.375 2.5,0.917 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 2.833,1.927 3.281,2.156 0.448,0.229 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C364797C03
1.542,0.104 1.917,0.333 0.375,0.229 0.271,1.677 0.271,1.521 0.271,1.521 0.698,1.219 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 0.094,1.75 0.625,1.958 0.531,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (SLIP INDICATOR LIGHT)
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light SLIP indicator light OFF or ON OFF: Indicator light off
ON: Indicator light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Slip Indicator Light
50003 105 304

g.

Check the GTS display condition of the slip indicator light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON