Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (w/ VSC) › from 2017.01
RM25T0E _54 Brake _029916 BRAKE SYSTEM (OTHER) _0282726 BRAKE MASTER CYLINDER(w/ VSC) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(w/ VSC)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD

Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for LHD)

a.
C375471

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install a new brake master cylinder gasket to the brake master cylinder sub-assembly.


c.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure foreign matter does not attach to the master cylinder piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



d.
C375473

Connect the brake fluid level warning switch connector to the brake master cylinder sub-assembly.


e.

Connect the clutch reservoir tube to the brake master cylinder sub-assembly.


f.
C375474C01
1.01,2.823 1.323,3.021 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 47201 3.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for RHD)

a.
C364629

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install a new brake master cylinder gasket to the brake master cylinder sub-assembly.


c.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure foreign matter does not attach to the master cylinder piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



d.
C364630C01
1.052,2.708 1.365,2.906 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




e.

Connect the brake fluid level warning switch connector to the brake master cylinder sub-assembly.


Hide 5.BLEED CLUTCH LINE (for RHD)