Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0106  Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0105.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>P0105

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem Either condition is met (2 trip detection logic):
(a) The manifold absolute pressure output is 2.5 V or higher for 10 seconds when idling the engine after warming it up.
(b) The manifold absolute pressure sensor output is 0.25 V or less for 10 seconds when the accelerator opening amount is 15% or more and the engine speed is 6000 rpm or less.
·

Vacuum hose connection

·

Manifold absolute pressure sensor


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0106 After warming up engine, idle engine for 10 seconds or more, and then drive vehicle under load (accelerator opening amount 15% or more) for 10 seconds

CAUTION / NOTICE / HINT

HINT:
·

If DTCs P0107 and P0108 are output simultaneously, the manifold absolute pressure sensor circuit may have an open or short. Perform troubleshooting for these DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0106)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0106 is output A
P0106 and other DTCs are output B




A

2.CHECK VACUUM HOSE CONNECTIONS

B

2.CHECK VACUUM HOSE CONNECTIONS
a.

Check the vacuum hose connections.

OK:

Vacuum hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CONNECT HOSE CORRECTLY
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After warming up the engine, idle the engine for 10 seconds or more, and then drive the vehicle under load (accelerator opening angle 15% or more) for 10 seconds or more.


f.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0106.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, drive the vehicle for 5 minutes, idle the engine for 5 minutes, and then check "All Readiness" again.



Result:
Proceed to
NEXT



NEXT

END

5.CONNECT HOSE CORRECTLY
Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED