Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.01
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contact of the EFI MAIN relay and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A403048E01
0.833,3.833 1.5,4.083 0.667,0.25 10 false FL MAIN 1,4.667 1.5,4.917 0.5,0.25 10 false Battery 0.833,2.583 1.25,2.833 0.417,0.25 10 false AM2 1.667,2.583 2.083,2.833 0.417,0.25 10 false EFI 1.667,1.167 2.083,1.417 0.417,0.25 10 false L21 1.667,1.333 3.333,1.583 1.667,0.25 10 false Ignition Switch Assembly 1.75,0.615 2,0.865 0.25,0.25 10 false 5 1.99,0.615 2.406,0.865 0.417,0.25 10 false AM2 2.531,0.615 2.948,0.865 0.417,0.25 10 false IG2 2.917,0.615 3.333,0.865 0.417,0.25 10 false 6 3.719,0.917 4.135,1.167 0.417,0.25 10 false IGN 4.25,1.5 4.917,1.667 0.667,0.167 10 false EFI-NO.2 2.75,1.833 3,2.083 0.25,0.25 10 false 5 3.667,1.833 4.083,2.083 0.417,0.25 10 false 3 2.75,2.25 3,2.5 0.25,0.25 10 false 2 3.667,2.25 4.083,2.5 0.417,0.25 10 false 1 3,2.75 3.75,3 0.75,0.25 10 false EFI MAIN 3.167,4.5 4,4.917 0.833,0.417 10 false *2: for RHD 5.833,5.083 6.25,5.333 0.417,0.25 10 false ECM 5.5,4.083 5.917,4.333 0.417,0.25 10 false E1 5.5,3.333 6,3.583 0.5,0.25 10 false MREL 5.5,2.583 5.917,2.833 0.417,0.25 10 false +B 5.5,2 5.917,2.25 0.417,0.25 10 false +B2 5.5,0.75 5.917,1 0.417,0.25 10 false IGSW 4.802,0.573 5.219,0.823 0.417,0.25 10 false 28*1 5.125,0.573 5.542,0.823 0.417,0.25 10 false 28*2 4.854,0.76 5.104,1.01 0.25,0.25 10 false I84 5.146,4.115 5.479,4.365 0.333,0.25 10 false C39 4.833,1.75 5.25,2 0.417,0.25 10 false 1*1 5.167,1.75 5.583,2 0.417,0.25 10 false 1*2 5.167,2.333 5.583,2.583 0.417,0.25 10 false 2*2 4.833,2.333 5.25,2.583 0.417,0.25 10 false 2*1 4.792,3.135 5.208,3.385 0.417,0.25 10 false 44*1 5.125,3.135 5.542,3.385 0.417,0.25 10 false 44*2 4.854,1.979 5.104,2.229 0.25,0.25 10 false I84 4.844,2.573 5.094,2.823 0.25,0.25 10 false I84 4.844,3.344 5.094,3.594 0.25,0.25 10 false I84 5.146,1.979 5.479,2.229 0.333,0.25 10 false A29 5.146,2.563 5.479,2.813 0.333,0.25 10 false A29 5.146,3.344 5.479,3.594 0.333,0.25 10 false A29 5.146,0.76 5.479,1.01 0.333,0.25 10 false A29 4.333,1.167 4.75,1.417 0.417,0.25 10 false 1 4.583,1.167 4.833,1.417 0.25,0.25 10 false 2 5.188,3.896 5.604,4.146 0.417,0.25 10 false 81 3.167,4.177 4,4.594 0.833,0.417 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)

2.INSPECT ECM (IGSW VOLTAGE)
A333590C02
0.865,2.271 1.396,2.583 0.531,0.313 1.135,0.271 1.635,0.573 0.5,0.302 1.51,2.271 2.031,2.583 0.521,0.313 1.969,1.292 2.208,1.958 2.208,1.958 2.417,1.958 true 2.25,3.156 2.479,4.094 2.479,4.094 2.656,4.094 true 2.438,1.875 3.125,2.115 0.688,0.24 10 false 81 (E1) 1.25,0.323 1.708,0.521 0.458,0.198 10 false C39 0.979,2.323 1.438,2.521 0.458,0.198 10 false I84 1.656,2.313 2.115,2.51 0.458,0.198 10 false A29 2.688,4.01 3.385,4.24 0.698,0.229 10 false 28 (IGSW) 0.99,2.083 1.302,2.281 0.313,0.198 10 false *A 1.677,2.073 1.99,2.271 0.313,0.198 10 false *B 0.083,0.073 0.24,0.271 0.156,0.198 10 false *a
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
I84-28 (IGSW) - C39-81 (E1) Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A29-28 (IGSW) - C39-81 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI MAIN RELAY (EFI MAIN)

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
3.INSPECT EFI MAIN RELAY (EFI MAIN)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)
a.

Remove the EFI MAIN relay from the Engine Room Relay Block Assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 3 - I84-2 (+B) Always Below 1 Ω
EFI MAIN relay terminal 3 - I84-1 (+B2) Always Below 1 Ω
EFI MAIN relay terminal 1 - I84-44 (MREL) Always Below 1 Ω
EFI MAIN relay terminal 3 or I84-2 (+B) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 3 or I84-1 (+B2) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 1 or I84-44 (MREL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 3 - A29-2 (+B) Always Below 1 Ω
EFI MAIN relay terminal 3 - A29-1 (+B2) Always Below 1 Ω
EFI MAIN relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
EFI MAIN relay terminal 3 or A29-2 (+B) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 3 or A29-1 (+B2) - Body ground Always 10 kΩ or higher
EFI MAIN relay terminal 1 or A29-44 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - ECM)

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BATTERY)
a.

Remove the EFI MAIN relay from the Engine Room Relay Block Assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
EFI MAIN relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - BATTERY)

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)
a.

Remove the EFI MAIN relay from the Engine Room Relay Block Assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Click here


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L21-6 (IG2) - I84-28 (IGSW) Always Below 1 Ω
L21-6 (IG2) or I84-28 (IGSW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L21-6 (IG2) - A29-28 (IGSW) Always Below 1 Ω
L21-6 (IG2) or A29-28 (IGSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

8.INSPECT IGNITION SWITCH ASSEMBLY
a.
A222467C06
0.271,1.885 0.646,2.156 0.375,0.271 1.938,2.156 2.219,2.833 false 2.26,2.146 2.813,2.688 false 0.177,0.188 0.573,0.396 0.396,0.208 10 false *a 2.271,2.781 2.563,2.979 0.292,0.198 10 false IG2 2.865,2.667 3.188,2.833 0.323,0.167 10 false AM2 0.333,1.927 0.792,2.125 0.458,0.198 10 false L21
*a Component without harness connected
(Ignition Switch Assembly)


Disconnect the ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Ignition Switch Position Specified Condition
5 (AM2) - 6 (IG2) ON Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY