Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2017.01–2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When a key is inserted into the ignition key cylinder, the transponder key amplifier receives the key ID code and sends it to the transponder key ECU assembly.

·

If an error in communication between the transponder key amplifier and transponder key ECU assembly occurs, this symptom may occur.


WIRING DIAGRAM

B278720E11
0.875,0.771 1.719,1.604 0.844,0.833 10 false Transponder Key Coil 1.24,2.125 3.479,2.792 2.24,0.667 10 false Transponder Key Amplifier 4.948,2.125 7.083,2.729 2.135,0.604 10 false Transponder Key ECU Assembly 1.24,1.948 1.844,2.125 0.604,0.177 10 false L28 4.948,1.948 5.563,2.135 0.615,0.188 10 false L30 5.5,0.354 6.115,0.698 0.615,0.344 10 false VC5 5.177,0.24 5.427,0.76 0.25,0.521 10 false 14 3.406,0.24 3.708,0.5 0.302,0.26 10 false 1 5.188,0.615 5.406,0.948 0.219,0.333 10 false 15 3.406,0.615 3.969,0.948 0.563,0.333 10 false 4 5.25,0.969 5.438,1.406 0.188,0.438 10 false 4 3.406,0.969 4.125,1.146 0.719,0.177 10 false 5 5.25,1.333 5.458,1.75 0.208,0.417 10 false 5 3.406,1.333 4.531,1.656 1.125,0.323 10 false 7 5.5,0.708 6.219,1 0.719,0.292 10 false CODE 5.5,1.073 6.438,1.354 0.938,0.281 10 false TXCT 5.49,1.438 6.417,1.729 0.927,0.292 10 false AGND 3.042,0.26 3.427,0.625 0.385,0.365 10 false VC5 1.833,0.219 2.281,0.625 0.448,0.406 10 false ANT2 1.833,1.625 2.323,1.938 0.49,0.313 10 false ANT1 2.917,0.615 3.448,0.969 0.531,0.354 10 false CODE 2.948,0.979 3.448,1.365 0.5,0.385 10 false TXCT 2.917,1.344 3.479,1.927 0.563,0.583 10 false AGND

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine and ECT > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 61

Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK SECURITY INDICATOR LIGHT OPERATION

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 61 681
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK SECURITY INDICATOR LIGHT OPERATION
4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK SECURITY INDICATOR LIGHT OPERATION
5.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER ENGINE STARTS

NG

7.REPLACE TRANSPONDER KEY AMPLIFIER
6.CHECK WHETHER ENGINE STARTS
a.

Using another registered door key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

11.REPLACE KEY

B

7.REPLACE TRANSPONDER KEY AMPLIFIER

Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered door key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE)

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

11.REPLACE KEY
11.REPLACE KEY
a.

Replace the key.

NOTICE:

Key ID code registration is necessary when replacing the key, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for SFI System)
NG (for ECD System)



OK

END (KEY WAS DEFECTIVE)

NG (for SFI System)

NG (for ECD System)