CHECK TRANSPONDER KEY ECU ASSEMBLY
Disconnect the L30 transponder key ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| L30-5 (GND) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| L30-1 (+B) - L30-5 (GND) | Input | P - W-B | Battery | Always | 11 to 14 V | +B |
| L30-2 (IG) - L30-5 (GND) | Input | B-Y - W-B | Ignition switch | Ignition switch off | Below 1 V | IG SW |
| Ignition switch ON | 11 to 14 V | |||||
| L30-3 (KSW) - L30-5 (GND) | Input | B-R - W-B | Unlock warning switch signal | No key in ignition key cylinder | 10 kΩ or higher | Key SW/B2780 |
| Key in ignition key cylinder | Below 1 Ω |
Reconnect the L30 transponder key ECU assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| L30-8 (IND) - L30-5 (GND) | Output | G-R - W-B | Security indicator light signal | No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) | Pulse generation | Immobiliser |
| Key in ignition key cylinder (immobiliser system unset) | Below 1 V | |||||
| L30-9 (D) - L30-5 (GND) | Input/Output | W - W-B | DLC3 communication | Without communication | Below 1 V | - |
| During communication | Pulse generation | |||||
| L30-4 (ANT1) - L30-5 (GND) | Input/Output | P - W-B | Transponder key amplifier power source | No key in ignition key cylinder | 4 to 6 V | - |
| Within 3 seconds of inserting key into ignition key cylinder | Pulse generation (See waveform 1) |
|||||
| L30-15 (ANT2) - L30-5 (GND) | Input/Output | W - W-B | Transponder key amplifier communication signal | No key in ignition key cylinder | 4 to 6 V | - |
| Within 3 seconds of inserting key into ignition key cylinder | Pulse generation (See waveform 2) |
|||||
| L30-12 (EFII) - L30-5 (GND) | Input | G - W-B | ECM input signal | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 3) |
E/G Start Permission |
| L30-13 (EFIO) - L30-5 (GND) | Output | G-Y - W-B | ECM output signal | Ignition switch off | Below 1 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 4) |
Using an oscilloscope, check the waveform.
Waveform 1 (Reference)
| Tester Connection | L30-4 (ANT1) - L30-5 (GND) |
| Tool Setting | 20 V/DIV., 2 s./DIV. |
| Condition | Within 3 seconds of inserting key into ignition key cylinder |
Waveform 2 (Reference)
| Tester Connection | L30-15 (ANT2) - L30-5 (GND) |
| Tool Setting | 20 V/DIV., 2 s./DIV. |
| Condition | Within 3 seconds of inserting key into ignition key cylinder |
Waveform 3 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Tester Connection | L30-12 (EFII) - L30-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
Waveform 4 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Tester Connection | L30-13 (EFIO) - L30-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
CHECK ECM (for 1GR-FE)
| *A | for RHD | *B | for LHD |
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.
Measure the, voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| A29-10 (IMO) - C39-81 (E1) *1 I84-10 (IMO) - C39-81 (E1) *2 |
Output | G - BR | Transponder key ECU assembly output signal | Ignition switch off | 11 to 14 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 1) |
E/G Start Permission | ||||
| A29-11 (IMI) - C39-81 (E1) *1 I84-11 (IMI) - C39-81 (E1) *2 |
Input | G-Y - BR | Transponder key ECU assembly input signal | Ignition switch off | Below 1 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 2) |
E/G Start Permission |
*1: for RHD
*2: for LHD
Using an oscilloscope, check the waveform.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Tester Connection | A29-10 (IMO) - C39-81 (E1) *1 I84-10 (IMO) - C39-81 (E1) *2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for RHD
*2: for LHD
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Tester Connection | A29-11 (IMI) - C39-81 (E1) *1 I84-11 (IMI) - C39-81 (E1) *2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for RHD
*2: for LHD
CHECK ECM (for 1VD-FTV)
| *A | for RHD | *B | for LHD |
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.
Measure the, voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| A29-10 (IMO) - C39-81 (E1)*1 I84-10 (IMO) - C39-81 (E1)*2 |
Output | G - BR | Transponder key ECU assembly output signal | Ignition switch off | 11 to 14 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 1) |
E/G Start Permission | ||||
| A29-11 (IMI) - C39-81 (E1)*1 I84-11 (IMI) - C39-81 (E1)*2 |
Input | G-Y - BR | Transponder key ECU assembly input signal | Ignition switch off | Below 1 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation (See waveform 2) |
E/G Start Permission |
*1: for RHD
*2: for LHD
Using an oscilloscope, check the waveform.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Item | Content |
|---|---|
| Tester Connection | A29-10 (IMO) - C39-81 (E1)*1 I84-10 (IMO) - C39-81 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for RHD
*2: for LHD
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 510 ms |
| Item | Content |
|---|---|
| Tester Connection | A29-11 (IMI) - C39-81 (E1)*1 I84-11 (IMI) - C39-81 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for RHD
*2: for LHD