Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B2793  Transponder Chip Malfunction  B2794  Unmatched Encryption Code  B2797  Communication Malfunction No. 1  B2798  Communication Malfunction No. 2  


DESCRIPTION

·

DTC B2793 is stored when a malfunction is found in the key during key ID code registration or a key ID code is not registered normally. Replace the key if key ID code registration cannot be performed normally and this DTC is output.

·

DTC B2794 is stored when a key with an incomplete key ID code is inserted into the ignition key cylinder.

·

DTC B2797 is stored when a key with a BCC malfunction is inserted into the ignition key cylinder.

·

DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2793 Transponder Chip Malfunction A transponder chip malfunction (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.


B2794 Unmatched Encryption Code A key with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.


B2797 Communication Malfunction No. 1 A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.


B2798 Communication Malfunction No. 2 Key ID code identification cannot be completed within the specified time (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2793 Abnormal Status
B2794 Different Encrypt Code
B2797 Bcc Malfunction
B2798 Frame Error

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:
·

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.

·

If DTC B2793, B2794, B2797 or B2798 are stored, clear the DTCs before checking the next key.



OK:

DTC B2793, B2974, B2797 or B2798 is not output.



Result:
Result Proceed to
DTCs are not output A
DTCs are output for all of the keys B
DTCs are output for any of the keys C



A

B

3.CHECK CONNECTION OF CONNECTOR

C

REPLACE KEY THAT DTC IS OUTPUT

3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.


b.

Check that the engine starts with the key.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

4.CHECK TRANSPONDER KEY COIL
4.CHECK TRANSPONDER KEY COIL
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260


c.

Check that the engine starts with the key.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY