Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B493891E01
5.031,2.104 7.156,2.49 2.125,0.385 10 false Transponder Key ECU Assembly 5.042,1.906 5.5,2.104 0.458,0.198 10 false L30 5.656,1.021 6.115,1.219 0.458,0.198 10 false IND 5.438,1.021 5.896,1.219 0.458,0.198 10 false 8 0.323,2.052 2.448,2.438 2.125,0.385 10 false Combination Meter Assembly 0.323,1.875 0.781,2.073 0.458,0.198 10 false L26 1.219,1.156 1.677,1.354 0.458,0.198 10 false LP 1.5,1.01 1.958,1.208 0.458,0.198 10 false 11

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Disconnect the L25 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L26-11 (LP) - L30-8 (IND) Always Below 1 Ω
L26-11 (LP) - Body ground Always 10 kΩ or higher
L30-8 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the L30 transponder key ECU assembly connector.


b.
C363466C02
1.385,0.271 1.99,0.552 0.604,0.281 2.823,0.552 2.625,0.552 2.625,0.552 2.448,1.365 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.521,0.281 1.833,0.438 0.313,0.156 10 false L26 2.885,0.479 3.323,0.667 0.438,0.188 10 false LP
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the voltage and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L26-11 (LP) - Body ground Ignition switch off Pulse generation
Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY