ENGINE CONTROL SYSTEM
| *1 | ECM | *2 | Atmospheric Pressure Sensor |
| *3 | Accelerator Pedal Position Sensor | *4 | Ignition Switch Signal |
| *5 | Starter Signal | *6 | Vehicle Speed Signal |
| *7 | Battery Voltage | *8 | DLC3 |
| *9 | Other Signal | *10 | Stop Light Switch |
| *11 | Generator | *12 | No. 2 Glow Relay |
| *13 | No. 1 Glow Relay | *14 | No. 2 Injector Driver |
| *15 | No. 1 Injector Driver | - | - |
| *1 | Fuel Supply Pump Assembly | *2 | Fuel Tank |
| *3 | Suction Control Valve | *4 | Fuel Temperature Sensor |
| *5 | Fuel Pressure Sensor | *6 | Common Rail RH |
| *7 | Pressure Limiter | *8 | Common Rail LH |
| *9 | Intercooler | *10 | Intake Air Temperature Sensor |
| *11 | Diesel Throttle Body (for Bank 1) | *12 | Diesel Throttle Body (for Bank 2) |
| *13 | Manifold Absolute Pressure Sensor | *14 | Glow Plug |
| *15 | Camshaft Position Sensor | *16 | Fuel Injector |
| *17 | Engine Coolant Temperature Sensor | *18 | Crankshaft Position Sensor |
| *19 | Turbocharger | *20 | Mass Air Flow Meter |
| *21 | Vacuum Regulating Valve | - | - |
COMMON RAIL SYSTEM DESCRIPTION
The common rail system uses high-pressure fuel to improve fuel economy and to provide robust engine power, while suppressing engine vibration and noise.
This system stores fuel, which has been pressurized and supplied by the fuel supply pump assembly, in the common rail. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM regulates the fuel injection timing and volume by using the EDU to provide an electric current to the solenoid valve in the injector. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system has a 2-Way Valve (TWV) inside the injector to open and close the fuel passage. As a result, both fuel injection timing and fuel injection volume can be precisely regulated by the ECM.
The common rail system provides two split fuel injections. In order to soften combustion shock, this system performs "pilot-injection" as the subsidiary fuel injection prior to the main-injection. This helps to reduce engine vibration and noise.
| *A | Air-cooled Type | *B | Water-cooled Type |
| *1 | Sensors | *2 | ECM |
| *3 | No. 1 EDU | *4 | No. 2 EDU |
| *5 | Suction Control Valve | *6 | Fuel Temperature Sensor |
| *7 | Fuel Supply Pump Assembly | *8 | Common Rail RH |
| *9 | Fuel Pressure Sensor | *10 | Fuel Filter |
| *11 | Fuel Cooler | *12 | Fuel Cooler |
| *13 | Fuel Injector | *14 | Fuel Tank |
| *15 | Common Rail LH | *16 | Pressure Limiter |
| *17 | High Pressure Fuel | *18 | Return Fuel |
| *19 | Suction Fuel | - | - |
| Component | Description |
|---|---|
| Common rail | Stores high-pressure fuel produced by fuel supply pump assembly |
| Fuel supply pump assembly | Operated by crankshaft. Supplies high-pressure fuel to common rail. |
| Fuel Injector | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor | Monitors internal fuel pressure of common rail and sends signals to ECM |
| Pressure limiter | Opens pressure limiter valve to reduce internal pressure in common rail when fuel press exceeds specified level |
| Suction control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
This table indicates typical DTCs for each malfunction occurrence.
| Component | Trouble Area | DTC No. |
|---|---|---|
| Fuel Injector | Open or short in injector circuit | P062D, P062E, P1238, P0093* |
| Stuck open | P0093, P1238 | |
| Stuck closed | P1238 | |
| Fuel pressure sensor | Open or short in fuel pressure sensor circuit or pressure sensor output fixed | P0087, P0190, P0192, P0193 |
| Pressure limiter | Stuck open | P0093 |
| Stuck closed | P0088* | |
| Suction control valve | Open or short in suction control valve circuit | P0627, P1229, P0088* |
| Stuck open | P1229, P0088* | |
| Stuck closed | - | |
| Injector driver (EDU) | Faulty EDU | P0093*, P062D*, P062E*, P1238* |
| Common rail system (Fuel system) | Fuel leaks in high-pressure areas | P0093 |
*: There may be no DTC output depending on the condition of the malfunction.
| DTC No. | Description |
|---|---|
| P0087 | Fuel pressure sensor output does not change |
| P0088 | Internal fuel pressure too high (240 MPa [2477 kgf/cm2, 34800 psi] or more) |
| P0093 | Fuel leaks in high-pressure areas |
| P0190 | Open or short in fuel pressure sensor circuit (Low or high output) |
| P0192 | Open or short in fuel pressure sensor circuit (Low output) |
| P0193 | Open or short in fuel pressure sensor circuit (High output) |
| P062D | Open or short in No. 1 injector driver or injector circuit |
| P062E | Open or short in No. 2 injector driver or injector circuit |
| P0627 | Open or short in suction control valve circuit |
| P1229 | Fuel over-feed |
| P1238 | Injection malfunction; excludes open or short in injector circuit |
INJECTION CONTROL SYSTEM DESCRIPTION
The ECM controls the fuel injection system by using the injectors and fuel supply pump assembly. The ECM regulates the fuel injection volume and fuel injection timing by controlling the duration and timing of the electric current provided to the solenoid valve in the injector. The ECM regulates injection pressure by controlling the suction control valve located in the fuel supply pump assembly.
The feed pump is used to pump fuel from the fuel tank to the fuel supply pump assembly.
| *1 | Accelerator Pedal Position Sensor | *2 | Camshaft Position Sensor |
| *3 | Crankshaft Position Sensor (NE signal) | *4 | Other Sensors |
| *5 | ECM | *6 | No. 1 EDU |
| *7 | No. 2 EDU | *8 | Fuel Injector (#1, #4, #6, #7) |
| *9 | Common Rail LH | *10 | Pressure Limiter |
| *11 | to Fuel Tank | *12 | Fuel Injector (#2, #3, #5, #8) |
| *13 | Fuel Pressure Sensor | *14 | Common Rail RH |
| *15 | Orifice | *16 | Solenoid Valve |
| *17 | TWV | *18 | Orifice |
| *19 | Control Chamber | *20 | Piston |
| *21 | Nozzle Needle | *22 | Injector |
| *23 | Fuel Tank | *24 | Feed Pump |
| *25 | Suction Control Valve | *26 | Check Valve |
| *27 | Outer Cam | *28 | Plunger |
| *29 | Inner Cam | *30 | Fuel Supply Pump Assembly |
FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
Due to the rotation of the inner cam (eccentric cam), the outer cam pushes plunger A upward as illustrated below. The force of the spring pulls plunger B and C. As a result, plunger B and C draw fuel in, and plunger A pumps fuel at the same time.
SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION
The ECM controls the suction control valve operation to regulate the fuel volume that is pumped by the fuel supply pump assembly to the common rail. This control is performed to adjust the internal fuel pressure of the common rail to the targeted injection pressure.
Small opening of the suction control valve:
When the opening of the suction control valve is small, the fuel suction path is kept narrow. Therefore the transferable fuel volume is reduced (*A).
The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum (*B).
Pumping will start when the fuel pressure becomes higher than the fuel press (*C).
Large opening of the suction control valve:
When the opening of the suction control valve is large, the fuel suction path is kept wide. Therefore the transferable fuel volume is increased (*D).
If the plunger stroke is full, the suction volume becomes large because of the wide path (*E).
Pumping will start when the fuel pressure becomes higher than the fuel press (*F).